Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

115

CURRENT MODE (052)
Selection

Set the current mode for HART communication.

Selection:

• Signaling

Measured value transmission by the current value

• Fixed

Fixed current 4.0 mA (multidrop mode)
(Measured value transmission only via HART digital communication)

Factory setting:

Signaling

BUS ADDRESS (345)
Entry

Enter the address for the exchange of data with the HART protocol.
(HART 5.0: range 0 to 15, wherein if the address = 0 this produces the "Signaling"
setting; HART 6.0/7.0: range 0 to 63)

Factory setting:

0

DEVICE TYPE (351)
Display

Displays the device type in decimal numerical format, here Deltabar S: 23
The extended device type is a composition of the manufacturer number (17) and the
device type (23).

Prerequisite:

• Deltabar S differential pressure transmitter

DEVICE TYPE (802)
Display

Displays the device type in decimal numerical format, here Cerabar S: 24
The extended device type is a composition of the manufacturer number (17) and the
device type (24).

Prerequisite:

• Pressure transmitter Cerabar S

DEVICE TYPE (002)
Display

Displays the device type in decimal numerical format, here Deltapilot S: 26
The extended device type is a composition of the manufacturer number (17) and the
device type (26).

Prerequisite:

• Pressure transmitter Deltapilot S

DEVICE REVISION (699)
Display

Displays the device revision

BURST MODE
Selection

Switches "Burst Mode" function on and off.

Selection:

• On
• Off

Prerequisite:

• Digital communication

BURST OPTION
Entry

Use this parameter to specify which command is sent to the master.

Voraussetzung:

• Digital communication

Factory setting:

3 (HART commando 3)

PREAMBLE NUMBER (036)
Entry

Enter the number of preambles in the HART protocol. (Synchronisation of the modem
modules along a transmission path, each modem module could "swallow" a byte - at least
2 bytes must arrive.)

Input range:

2...20

Factory setting:

5

MANUFACTOR ID (432)
Display

Displays the manufacturer number in a decimal numerical format.
Here: 17 Hauser

HART MESSAGE (271)
Entry

Enter message (max. 32 alphanumeric characters).
On command from the master, this message is sent via the HART protocol.

Factory setting:

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
or as per order specifications

Table 23: (GROUP SELECTION



) OPERATING MENU



TRANSMITTER INFO



HART DATA

Parameter name

Description

«
...
113
114
115
116
117
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: 3M Страницы: 26

Бренд: Pacbrake Страницы: 9

iVu Plus BCR Gen2 Series

Бренд: Banner Страницы: 12

Бренд: Banner Страницы: 28

Бренд: Banner Страницы: 155

Бренд: Banner Страницы: 64

Бренд: Banner Страницы: 8

Бренд: Banner Страницы: 2

Бренд: Banner Страницы: 8

Бренд: Banner Страницы: 12

Бренд: Hama Страницы: 40

Бренд: Rave Sports Страницы: 16

Бренд: BAFANG Страницы: 4

PORTABLE AIR CONDITIONER & COOLER

Бренд: Icebreeze Страницы: 12

Бренд: Kampmann Страницы: 36

Бренд: Sami Страницы: 10

Legend G3 738 NGK

Бренд: Valor Страницы: 6

Бренд: Sacred Sun Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды