Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 156

background image

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

112

Hauser

CURR. CHARACT.
(694), (695), (696), (764)
Selection

Select curve of current output.

Options:

P01-xxxxxxxx-05-xx-xx-xx-009

Fig. 43:

Illustration of current output curves

1

Linear: lower range value = 4 mA, upper range value = 20 mA

2

Bi-linear: lower range value = 4 mA, centre or zero = 20 mA,
upper range value = 4 mA

3

Linear inverse: lower range value = 20 mA, upper range value = 4 mA

4

Bi-linear inverse: lower range value = 20 mA, centre or zero = 4 mA,
upper range value = 20 mA

LRV

Lower range value

URV

Upper range value

I

Current

X

Measured value (Pressure/Level/Flow)
The "CURR. CHARACT." function refers to the operating mode previously
selected.

The 3-digit ID number on the on-site display depends on the MEASURING MODE
selected:
– (694): MEASURING MODE "Pressure" or MEASURING MODE "Flow" with the

setting for LINEAR/SQROOT "Differential pres.

– (695): MEASURING MODE "Flow" with the setting LINEAR/SQROOT "Flow (square

root)"

– (696): MEASURING MODE "Level", LEVEL MODE "Linear" or "Pressure Linearized"

and LEVEL MODE "Height Linearized" with the setting for ASSIGN CURRENT "Level"

– (764): MEASURING MODE "Level", LEVEL MODE "Height Linearized" with the

setting for ASSIGN CURRENT "Tank content"

Factory setting:

Linear

OUTPUT FAIL MODE (388)
Entry

Select the current value in the event of an alarm.
In the event of an alarm, the current and the bargraph assume the current value specified
with this parameter.

Options:

• Max. alarm (110%): can be set between 21...23 mA
• Hold meas. value: last measured value is kept.
• Min. alarm (–10%): 3.6 mA



See also this table SET MAX. ALARM and Operating Instructions BA00270P (Deltabar

S), BA00271P (Cerabar S) or BA00332P (Deltapilot S), Section 8.2.1. "Setting current
output for alarm".

Factory setting:

Max. alarm 110% (22 mA)

Table 22: (GROUP SELECTION



) OPERATING MENU



OUTPUT

Parameter name

Description

LRV

➂

➁

➀

4

m

A

0

2

0

m

A

➁

➃

➃

URV

URV

I

X

«
...
110
111
112
113
114
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Bicycle Accessories

Бренд: Baby Jogger Страницы: 20

Wireless Temperature/Humidity Station

Бренд: DAVIS Страницы: 8

Бренд: Hagan Страницы: 32

Бренд: Jabra Страницы: 2

SP200 - QUICKSTART GUIDE 1

Бренд: Jabra Страницы: 2

JABRA FREEWAY HFS100

Бренд: Jabra Страницы: 40

BT150 - Headset - Over-the-ear

Бренд: Jabra Страницы: 2

AquaSensors AnalogPlus 1.0

Бренд: Thermo Scientific Страницы: 24

Бренд: Hartan Страницы: 86

Tinker PIZZA-BOX/ THERMO-BOX

Бренд: RIESE & MULLER Страницы: 4

Бренд: R&G Страницы: 10

Бренд: Masterack Страницы: 4

Бренд: Over Armour Offroad Страницы: 5

Бренд: ECG Страницы: 24

Бренд: Polaroid Страницы: 64

Бренд: SRAM Страницы: 26

1501-3120-6010-100

Бренд: S+S Regeltechnik Страницы: 16

Бренд: echoflex Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды