Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 92

Страница: 92 / 156

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Hauser

MEASURING MODE
Selection

Select the measuring mode.
The operating menu is structured according to the selected measuring mode.

Warning!

If the measuring mode is changed, the span setting (URV) must be verified in the
"Calibration"



"Basic Setup" operating menu and, if necessary, reconfigured.

Prerequisite:

• Digital communication

Options:

• Pressure
• Level
• Deltabar S: Flow

Factory setting:

• Cerabar S and Deltabar S: Pressure
• Deltapilot S: Level

PRESS. ENG. UNIT (060)
Selection

Select pressure unit.
If a new pressure unit is selected, all pressure-specific parameters are converted and
displayed with the new unit.

Options:

• mbar, bar
• mmH2O, mH2O, inH2O, ftH2O

• Pa, hPa, kPa, MPa
• psi
• mmHg, inHg

• Torr
• g/cm

, kg/cm

• lb/ft

• atm
• gf/cm

, kgf/cm

• User unit,



See also the following parameter description for CUSTOMER UNIT P and

CUST. UNIT FACT. P.

1) The conversion factor of the pressure units refers to a reference temperature of 4 °C
(39.2 °F).
2) The conversion factor of the pressure units refers to a reference temperature of 0 °C
(32 °F).

Factory setting:

Depends on the sensor nominal measuring range mbar or bar or as per order
specifications

CUSTOMER UNIT P (075)
Entry

Enter text (unit) for customer-specific pressure unit.
You can enter a maximum of eight alphanumeric characters here.



Содержание Deltabar S PMD70





























































































































































Результаты поиска

Содержание Deltabar S PMD70

Отзывы:

Похожие инструкции для Deltabar S PMD70

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar S PMD70, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar S PMD70

Отзывы:

Похожие инструкции для Deltabar S PMD70

Бренды по названию

Популярные бренды