Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 156

background image

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

Description of parameters

Hauser

87

CALIBRATION MODE (392)
Selection

Select the calibration mode for the calibration of the 1st measured variable.

Options:

• Wet

Wet calibration takes place by filling the container. This calibration mode requires two
pressure-level value pairs to be entered. In the case of two different levels, the level
value is entered and the pressure measured at this moment is assigned to the level
value.



See also the following parameter description for EMPTY CALIB., EMPTY

PRESSURE, FULL CALIB. and FULL PRESSURE.

• Dry

Dry calibration is a theoretical calibration which you can carry out even if the device is
not mounted or the container is empty.
– For the "Level" measured variable, the density of the fluid (



see Page 88, ADJUST

DENSITY) must be entered.

– For the "%" measured variable, the density of the fluid must be entered and a level

assigned to the 100 % point (



see Page 88, ADJUST DENSITY and 100% POINT).

If the measurement should not start at the mounting location of the device, a level
offset must be entered (



see Page 90, ZERO POSITION).

!

Note!

If the change to dry calibration is made after a wet calibration, the density must be
entered correctly using the ADJUST DENSITY and DENSITY PROCESS parameter before
changing the calibration mode.



See also Page 97.

Factory setting:

Wet

EMPTY CALIB. (314)
Entry

Enter level value for the lower calibration point (container empty).
The container is either empty or part full. By entering a value for this parameter, you are
assigning a level value to the pressure present at the device.



See also EMPTY

PRESSURE.

Prerequisite:

• CALIBRATION MODE = Wet

Factory setting:

0.0

EMPTY PRESSURE (710)
Display

Displays the pressure value for the lower calibration point (container empty).



See also EMPTY CALIB.

Prerequisite:

• CALIBRATION MODE = Wet

FULL CALIB. (315)
Entry

Enter level value for the upper calibration point (container full).
The container is either completely or almost full. By entering a value for this parameter,
you are assigning a level value to the pressure present at the device.



See also FULL

PRESSURE.

Prerequisite:

• CALIBRATION MODE = Wet

Factory setting:

100.0

FULL PRESSURE (711)
Display

Displays the pressure value for the upper calibration point (container full).



See also FULL CALIB.

Prerequisite:

• CALIBRATION MODE = Wet

Factory setting:

High sensor limit (





see PRESS. SENS HILIM, Page 119)

ADJUSTED DENSITY (810)
Display

Displays the density calculated from the upper and lower level point.

Prerequisite:

• COMB. MEASURAND = Height and Volume, CALIBRATION MODE = Wet
• COMB. MEASURAND = Height and Mass, CALIBRATION MODE = Wet
• COMB. MEASURAND = Height and %, CALIBRATION MODE = Wet

Table 13: (GROUP SELECTION



) OPERATING MENU



SETTINGS



BASIC SETUP "Level",

LEVEL MODE "Height Linearized"

Parameter name

Description

«
...
85
86
87
88
89
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

IMAGEPRESS C7010VPS

Бренд: Canon Страницы: 4

Бренд: Quintex Страницы: 29

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 2

DS-KABD8003-RS3

Бренд: HIKVISION Страницы: 3

Бренд: VOLTCRAFT Страницы: 2

BOS 21M-UUI-RP30-S4

Бренд: Balluff Страницы: 70

MOLLE PANELS RAM 2500

Бренд: PUTCO Страницы: 4

Бренд: Westfalia Страницы: 18

Бренд: HHD Страницы: 5

Бренд: CONVEY-ALL Страницы: 56

Бренд: Chamberlain Страницы: 4

Бренд: Gira Страницы: 8

Бренд: Subal Страницы: 13

Fit 4-All Music

Бренд: Variphone Страницы: 2

Бренд: Daikin Страницы: 18

Бренд: FORM FIT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды