Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 156

background image

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

64

Hauser

OUTPUT UNIT (023)
Options

Select unit for measured value display and MEASURED VALUE parameter (



Page 122).

!

Note!

The selected unit is used only to describe the measured value. This means that when
selecting a new output unit, the measured value is not converted.
Example:
• current measured value: 0.3 ft
• new output unit: m
• new measured value: 0.3 m (9.8 ft)

Options:

• %
• mm, cm, dm, m
• ft, inch
• cm

3

, dm

3

, m

3

,m

3

E

3

• l, hl
• ft

3

, ft

3

E

3

• gal, bbl, Igal
• g, kg, t
• lb, ton, oz

Factory setting:

%

HEIGHT UNIT (003)
Options

Select height unit. The measured pressure is converted to the chosen height unit using
the DENSITY UNIT and ADJUST DENSITY parameters.

Options:

• mm
• cm
• dm
• m
• inch
• ft

Factory setting:

m

CALIBRATION MODE (008)
Options

Select calibration mode.

Options:

• Wet

Wet calibration takes place by filling and emptying the container. The measured
pressure is converted to the chosen height unit using the HEIGHT UNIT, DENSITY
UNIT and ADJUST DENSITY parameters. In the case of two different levels, the level,
volume, mass or percentage value entered is assigned to the converted height value.

• Dry

Dry calibration is a theoretical calibration. For this calibration, specify two height-level
value pairs via the EMPTY CALIB., EMPTY HEIGHT, FULL CALIB. and FULL
HEIGHT parameters.

Factory setting:

Dry

DENSITY UNIT (001)
Options

Select density unit. The measured pressure is converted to a height using the HEIGHT
UNIT, DENSITY UNIT and ADJUST DENSITY parameters.

Options:

• g/cm

3

• kg/dm

3

• kg/m

3

• US lb/in

3

• US lb/ft

3

Factory setting:

kg/dm

3

ADJUST DENSITY (007)
Entry

Enter density of fluid. The measured pressure is converted to a height using the HEIGHT
UNIT, DENSITY UNIT and ADJUST DENSITY parameters.

Factory setting:

1.0

Table 9: (GROUP SELECTION



) OPERATING MENU



SETTINGS



BASIC SETUP "Level",

LEVEL SELECTION "Level Easy Height"

«
...
62
63
64
65
66
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

nanoe CZ-CNEXU1

Бренд: Panasonic Страницы: 108

Бренд: ZAPTEC Страницы: 64

Бренд: ZAPTEC Страницы: 24

Бренд: Federal Signal Corporation Страницы: 13

Бренд: Hammond Страницы: 754

Бренд: Manfrotto Страницы: 2

Бренд: Danfoss Страницы: 4

Бренд: Labelmate Страницы: 2

AdvancedPunch Pro

Бренд: GBC Страницы: 92

Бренд: Oki Страницы: 3

Бренд: Manfrotto Страницы: 2

Бренд: WÄRTSILÄ Страницы: 64

Бренд: Natibaby Страницы: 24

Бренд: Narvitech Страницы: 12

Бренд: Nautronic Страницы: 7

Бренд: NAPCO Страницы: 16

Бренд: VARIZOOM Страницы: 5

Бренд: VARIZOOM Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды