Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 156

background image

Appendix

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

142

Hauser

8.3

Confirming messages

Depending on the settings for the ALARM DISPL. TIME (



Page 129) and ACK. ALARM MODE

(



Page 128) parameters, the following measures should be taken to clear a message:

If the on-site display displays a message, you can delete it with the

F

-key.

If there are several messages, the on-site display shows the message which has the highest priority
(see also Section 8.1). Once you have deleted this message using the

F

-key, the message with the

next highest priority is displayed. You can use the

F

-key to delete each message, one after the other.

The ALARM STATUS parameter continues to display all the messages present.

9

Appendix

9.1

Operating menu for on-site display, Digital
communication

!

Note!
• The entire menu is depicted on the following pages.
• The menu has a different structure depending on the measuring mode selected. This means that

some function groups are only displayed for one measuring mode, e.g. "LINEARISATION"
function group for the Level measuring mode (Menu path: (GROUP SELECTION



)

OPERATING MENU



SETTINGS



BASIC SETUP).

• In addition, there are also parameters that are only displayed if other parameters are appropriately

configured. For example the Customer Unit P parameter is only displayed if the "User unit" option
was selected for the PRESS. ENG. UNIT parameter. These parameters are indicated with a "*".

• For a description of the parameters, please refer to chapter 7 "Description of parameters". The

exact dependency of individual parameters on one another is explained here.

Settings

1)

1)

Menu path for ALARM DISPL. TIME and ACK. ALARM MODE: (GROUP SELECTION



) OPERATING MENU



DIAGNOSTICS



MESSAGES

Measures

– ALARM DISPL. TIME = 0 s
– ACK. ALARM MODE = off

– Rectify cause of the message (see also Section 8.1).

– ALARM DISPL. TIME > 0 s
– ACK. ALARM MODE = off

– Rectify cause of the message (see also Section 8.1).
– Wait for the alarm display time to elapse.

– ALARM DISPL. TIME = 0 s
– ACK. ALARM MODE = on

– Rectify cause of the message (see also Section 8.1).
– Confirm message using ACK. ALARM parameter.

– ALARM DISPL. TIME > 0 s
– ACK. ALARM MODE = on

– Rectify cause of the message (see also Section 8.1).
– Confirm message using ACK. ALARM parameter.
– Wait for the alarm display time to elapse. If a message appears and the alarm

display time elapses before the message has been acknowledged, the message
will be cleared once it has been acknowledged.

«
...
140
141
142
143
144
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

CRD 2 00-1000S Series

Бренд: Symbol Страницы: 16

Бренд: Bang & Olufsen Страницы: 12

CSL Elite Racing Wheel

Бренд: FANATEC Страницы: 2

Бренд: FANATEC Страницы: 8

Бренд: FANATEC Страницы: 35

Бренд: Garmin Страницы: 26

Бренд: Garmin Страницы: 8

Бренд: Garmin Страницы: 72

Бренд: Uniden Страницы: 16

Бренд: Uniden Страницы: 20

Бренд: Hama Страницы: 56

USB 3.0 Dual Head Docking Station

Бренд: SIIG Страницы: 12

Бренд: Thunderbike Страницы: 11

Monarch Pass M321

Бренд: Wolfman Страницы: 5

Бренд: Waycon Страницы: 27

Бренд: Cheyenne Страницы: 348

Бренд: Vega Страницы: 36

Бренд: Yakima Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды