Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 156

background image

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

128

Hauser

SIM. LEVEL (714)
Entry

Enter simulation value.



See also SIMULATION MODE.

Prerequisite:

• MEASURING MODE = Level and SIMULATION MODE = Level

SIM. TANK CONT. (715)
Entry

Enter simulation value.



See also SIMULATION MODE.

Prerequisites:

• MEASURING MODE = Level, LEVEL MODE = Pressure Linearized and

SIMULATION MODE = Tank content

• MEASURING MODE = Level, LEVEL MODE = Height Linearized and

SIMULATION MODE = Tank content

SIM. CURRENT (270)
Entry

Enter simulation value.



See also SIMULATION MODE.

Prerequisite:

• SIMULATION MODE = Current value

Factory setting:

Current current value

SIM. ERROR NO. (476)
Entry

#

Warning!

The SIMULATION parameter overwrites fault states (alarm/warning) that are actually
present. When the simulation is ended, the fault states (alarm/warning) still persist but
are no longer displayed! When the device is restarted it returns to its fault state.

Enter message number.



See also SIMULATION MODE.



See also these Operating Instructions, Section 8.1 "Messages", "Code" table column.

Prerequisite:

• SIMULATION MODE = Alarm/Warning

Factory setting:

613 (simulation active)

Table 33: (GROUP SELECTION



) OPERATING MENU



DIAGNOSTICS



MESSAGES

Parameter name

Description

ALARM STATUS (046)
Display

Displays the current messages present.



See also these Operating Instructions,

Section 8.1. "Messages" and Section 8.3 "Confirming messages".

On-site display

• The measured value display shows the message with the highest priority.
• The ALARM STATUS parameter shows all the messages in descending order of

priority. You can scroll through all the messages present with the

O

or

S

key.

Operating program

• The "Status" field and the ALARM STATUS parameter show the message with the

highest priority.

LAST DIAG. CODE (564)
Display

Displays the last messages that occurred and were eliminated.

!

Note!

• On-site display: you can scroll through the last 15 messages with the

O

or

S

key.

• Digital communication: the last message appears on the display.
• Use the RESET ALL ALARMS parameter to delete the messages listed in the LAST

DIAG. CODE parameter.

ACK. ALARM MODE (401)
Selection

Switch on acknowledge alarm mode.



See also ACK. ALARM.

Options:

• On
• Off

Factory setting:

Off

Table 32: (GROUP SELECTION



) OPERATING MENU



DIAGNOSTICS



SIMULATION

Parameter name

Description

«
...
126
127
128
129
130
...
»

Содержание Deltabar S PMD70





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deltabar S PMD70

Бренд: K&M Страницы: 9

Бренд: IBS Страницы: 24

Бренд: Panasonic Страницы: 1

Бренд: Labelmate Страницы: 2

Бренд: Labnet Страницы: 2

Бренд: Nailor Страницы: 6

Бренд: Fisher-Price Страницы: 8

Бренд: Whispbar Страницы: 15

Бренд: Hama Страницы: 56

CV MY FIRST TRAMPOLINE AND ENCLOSURE

Бренд: Chad Valley Страницы: 15

Бренд: poly-planar Страницы: 2

Бренд: Tunturi Страницы: 37

Бренд: Cuisinart Страницы: 20

MDSEN-IR-277V-R2

Бренд: Larson Electronics Страницы: 2

Davis Compatible

Бренд: Calypso Страницы: 5

v.LOGiC Intelligent Solution V5-NTG46

Бренд: Caraudio-Systems Страницы: 18

Бренд: DeLOCK Страницы: 14

G01102.2 Series

Бренд: REV Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды