Endress+Hauser Deltabar S PMD70 Скачать руководство пользователя страница 120

Страница: 120 / 156

Description of parameters

Cerabar S/Deltabar S/Deltapilot S 4...20mA HART

120

Hauser

SENSOR MEAS.TYPE (581)
Display

Displays the sensor type.

• Deltabar S = differential
• Cerabar S with gauge pressure sensor = relative
• Cerabar S with absolute pressure sensor = absolute
• Deltapilot S = relative

Pmin SENS. DAMAGE (251)
Display

Displays the minimum permissible absolute pressure of the sensor (vacuum-proofing).

Pmax SENS. DAMAGE (252)
Display

Displays the maximum permissible absolute pressure of the sensor (overpressure-
proofing).

MAT. MEMBRANE (365)
Display

Displays the material of the process isolating diaphragm.

Factory setting:

As per version in the order code



For Deltabar S, see Technical Information TI00382P, for Cerabar S, see Technical

Information TI00383P or for Deltapilot S, see Technical Information TI00416P,
"Ordering information" section.

FILLING FLUID (366)
Display

Displays the filling fluid.

Tmin SENSOR (368)
Display

Displays the lower nominal temperature limit of the sensor.

Tmax SENSOR (369)
Display

Displays the upper nominal temperature limit of the sensor.

SENS H/WARE REV (487)
Display

Displays the revision number of the sensor hardware.
e.g.: 1

Table 26: (GROUP SELECTION



) OPERATING MENU



TRANSMITTER INFO



SENSOR DATA

(all measuring modes)

Parameter name

Description

Содержание Deltabar S PMD70





























































































































































Результаты поиска

Содержание Deltabar S PMD70

Отзывы:

Похожие инструкции для Deltabar S PMD70

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar S PMD70, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar S PMD70

Отзывы:

Похожие инструкции для Deltabar S PMD70

Бренды по названию

Популярные бренды