Endress+Hauser Deltabar FMD72 Скачать руководство пользователя страница 92

Страница: 92 / 108

Description of device parameters

Deltabar FMD72

Factory setting

According to order specifications

Order code (098)

Navigation

Diagnosis

Instrument info

Order Code (098)

Write permission

Parameter is read only. Only Hauser Service has write permission.

Description

Displays the order identifier.

Factory setting

According to order specifications

ENP version (099)

Navigation

Diagnosis

Instrument info

ENP Version (099)

Write permission

Operators/Service engineers/Expert

Description

Displays the ENP version
(ENP = electronic nameplate)

Config. counter (100)

Navigation

Diagnosis

Instrument info

Config. Counter (100)

Write permission

Operators/Service engineers/Expert

Description

Displays the configuration counter.
This counter is increased by one every time a parameter or group is changed. The counter counts
up to 65535 and then starts again at zero.

LRL sensor (101)

Navigation

Diagnosis

Instrument info

Sens. Limit HP

LRL Sensor (101)

Write permission

No write permissions. Parameter is read only.

Description

Displays the lower-range limit of the sensor module.

Содержание Deltabar FMD72













































































































Результаты поиска

Содержание Deltabar FMD72

Отзывы:

Похожие инструкции для Deltabar FMD72

Бренды по названию

Популярные бренды

Endress+Hauser Deltabar FMD72, Руководство по эксплуатации

Результаты поиска

Содержание Deltabar FMD72

Отзывы:

Похожие инструкции для Deltabar FMD72

Бренды по названию

Популярные бренды