Endress+Hauser Ceraphant PTP31B Скачать руководство пользователя страница 58

Страница: 58 / 92

Description of device parameters

Ceraphant PTC31B, PTP31B, PTP33B IO-Link

Hauser

Simulation Switch Output (OU2)

Simulation output 2 (for devices with 2 switch outputs)

Navigation

Display: DIAG → Simulation Switch Output (OU2)

IO-Link: Diagnosis → Simulation Switch Output (OU2)

Description

Switch output simulation.

If a simulation is active, a warning to this effect is displayed so that it is obvious to the user

that the device is in the simulation mode. A visual warning is indicated on the local display

(C485 - Simulation Active). The simulation must be ended actively via the menu. If the

device is disconnected from the power supply during the simulation and then power is

resupplied afterwards, the simulation mode is not resumed, and instead the device

continues operation in the measuring mode.

Options

• OFF

• OPN (switch output open)

• CLS (switch output closed)

Operating Mode (FUNC)

Navigation

Display: EF → Operating Mode (FUNC)

IO-Link: Parameter → Application → Sensor → Operating Mode (FUNC)

Description

Enables the desired behavior of output 2 (not IO-Link output)

Options

Options:

• OFF

• 4-20 mA (I) ((can only be selected if the device has been ordered with 4-20mA))

• DC-PNP (PNP)

Unit changeover (UNI)

Navigation

Display: EF → Unit changeover (UNI)

IO-Link: Parameter → Application → Sensor → Unit changeover (UNI)

Description

Select the pressure engineering unit. If a new pressure engineering unit is selected, all

pressure-specific parameters are converted.

Options

• bar

• kPa

• Mpa

• psi

Factory setting

Depends on order specifications.

Zero point configuration (ZRO)

Содержание Ceraphant PTP31B





























































































Результаты поиска

Содержание Ceraphant PTP31B

Отзывы:

Похожие инструкции для Ceraphant PTP31B

Бренды по названию

Популярные бренды

Endress+Hauser Ceraphant PTP31B, Руководство по эксплуатации

Результаты поиска

Содержание Ceraphant PTP31B

Отзывы:

Похожие инструкции для Ceraphant PTP31B

Бренды по названию

Популярные бренды