Endress+Hauser Ceraphant PTP31B Скачать руководство пользователя страница 50

Страница: 50 / 92

Repairs

Ceraphant PTC31B, PTP31B, PTP33B IO-Link

Hauser

Repairs

12.1 General notes

12.1.1 Repair concept

Repairs are not possible.

12.2 Return

The measuring device must be returned if the wrong device has been ordered or delivered.
As an ISO-certified company and also due to legal regulations, Hauser is obliged

to follow certain procedures when handling any returned products that have been in

contact with medium. To ensure swift, safe and professional device returns, please read

the return procedures and conditions on the Hauser website at

www.services.endress.com/return-material

12.3 Disposal

When disposing, separate and recycle the device components based on the materials.

Содержание Ceraphant PTP31B





























































































Результаты поиска

Содержание Ceraphant PTP31B

Отзывы:

Похожие инструкции для Ceraphant PTP31B

Бренды по названию

Популярные бренды

Endress+Hauser Ceraphant PTP31B, Руководство по эксплуатации

Результаты поиска

Содержание Ceraphant PTP31B

Отзывы:

Похожие инструкции для Ceraphant PTP31B

Бренды по названию

Популярные бренды