Endress+Hauser Cerabar M Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 92

background image

Cerabar M, Deltapilot M

Operation

Hauser

37

6.3.2

Structure of the operating menu

User
role

Sub-
menu

Meaning/use

Opera-
tor

Lan-
guage

Only consists of the "Language" parameter (000) where the operating language for the
device is specified.
The language can always be changed even if the device is locked.

Opera-
tor

Display/
operat.

Contains parameters that are needed to configure the measured value display (selecting
the values displayed, display format, etc.). With this submenu, users can change the meas-
ured value display without affecting the actual measurement.

Mainte-
nance

Setup

Contains all the parameters that are needed to commission measuring operations. This
submenu has the following structure:
•

Standard setup parameters

A wide range of parameters, which can be used to configure a typical application, is
available at the start. The measuring mode selected determines which parameters are
available.
After making settings for all these parameters, the measuring operation should be com-
pletely configured in the majority of cases.

•

"Extended setup" submenu

The "Extended setup" submenu contains additional parameters for more accurate config-
uration of the measurement, for converting the measured value and for scaling the out-
put signal.
This menu is split into additional submenus depending on the measuring mode selec-
ted.

Mainte-
nance

Diagno-
sis

Contains all the parameters that are needed to detect and analyze operating errors. This
submenu has the following structure:
•

Diagnostic list

Contains up to 10 currently active error messages.

•

Event logbook

Contains the last 10 error messages (no longer active).

•

Instrument info

Contains information for identifying the device.

•

Measured values

Contains all the current measured values.

•

Simulation

Is used to simulate pressure, level, current and alarm/warning.

•

Enter reset code

Expert

Expert

Contains all the parameters of the device (including those already in one of the other sub-
menus). The "Expert" submenu is structured by the function blocks of the device. It thus
contains the following submenus:
•

System

Contains all the device parameters that do not pertain either to the measurement or to
integration into a control system.

•

Measurement

Contains all the parameters for configuring the measurement.

•

Output

Contains all the parameters for configuring the current output.

•

Communication

Contains all the parameters for configuring the communication interface.

•

Application

Contains all the parameters for configuring the functions that go beyond the actual
measurement.

•

Diagnosis

Contains all the parameters that are needed to detect and analyze operating errors.

For an overview of the entire operating menu .

6.4

Operation with device display (optional)

A 4-line liquid crystal display (LCD) is used for display and operation. The local display

shows measured values, dialog texts, fault messages and notice messages. For easy opera-

tion the display can be taken out of the housing (see figure steps 1 to 3). It is connected to

the device via a 90 mm (3.54 in) long cable. The display of the device can be turned in 90°

«
...
35
36
37
38
39
...
»

Содержание Cerabar M





























































































Отзывы:

Нет отзывов

Похожие инструкции для Cerabar M

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

Бренд: Unico Страницы: 10

Бренд: Roland Страницы: 15

Бренд: JAMAR Technologies Страницы: 4

Бренд: Jamar Страницы: 60

Photo Research PR-810

Бренд: Jadak Страницы: 120

Бренд: Hanna Instruments Страницы: 2

Smart Photometer System iDip 570

Бренд: eXact Страницы: 16

Бренд: Chauvin Arnoux Страницы: 44

Бренд: Droplet Страницы: 35

Бренд: Sencore Страницы: 75

Бренд: truflo Страницы: 33

Бренд: Konica Minolta Страницы: 48

MarMonix MSL-765

Бренд: Farnell Страницы: 15

Бренд: Shimadzu Страницы: 22

Бренд: Omega Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды