manualshive.com logo in svg

Endress+Hauser Analytik Jena TOPwave, Руководство по эксплуатации, Страница: 53 / 79

Поделиться
Скачать
Endress+Hauser Analytik Jena TOPwave Скачать руководство пользователя страница 53

TOPwave 

Operating 

 

 

53 

 

1  Caustic soda 
2  Marble granulate 

 

Connect the cooler to a coolant water system with a maximum water temperature of 

20 °C (68 °F). The coolant water flow rate must be approx. 0.5 liters/min. 

6.7.2

 

Operating 

 

WARNING 

Always wear eye protection! 

Always wear safety glasses/goggles and protective gloves during work which may in-
volve contact with chemicals, that is, when working with acids, pressure vessels, during 

cleaning, etc.

 

 

 

WARNING 

Always wear safety glasses/goggles and protective gloves during work which may in-

volve contact with chemicals, that is, when working with acids, pressure vessels, during 

cleaning, etc.!

 

 

 

After the samples have been digested and cooled in the microwave open the vessels 

as described in the section "Sample Removal" p. 45. 

 

Then screw on the special cap for evaporating.CX 100 vessels: Put the spacer ring di-

rectly on the TFM–PTFE inline of the CX 100 vessel. 

 

WARNING 

It is important that the lid with the rupture disc be removed for evaporating and that it is 

never used for this procedure.

 

Evaporation cap for   
PM 60 und PL 100

 

Evaporation cap CX 100

 

Lid replacement 

Содержание Analytik Jena TOPwave
















































































Отзывы:

Нет отзывов