Endress+Hauser Analytik Jena Multi X 2500 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 124

background image

Function and layout of the multi X 2500

multi X 2500

20

Fig. 4

Electrical interfaces on the rear of the multi X 2500

1  USB connection to the control PC
2  External connection (to the pre-combustion adapter)
3  Auto-injector connection
4  Flame sensor connection (to the ABD)

5  Connection Cl module
6  Connection TOC module
7  Connection sampler (RS 232 bus)
8  Connection service

The control electronics are on the right-hand side of the rear panel of the basic device

behind the cover. The internal device control is used for power supply, controlling the
individual components of the basic device and the communication with the computer

and other connected system modules.
The electrical connections of the combustion furnace, the flame sensor and the
thermocouple are located right under the control electronics' cover. The connections

are only accessible in the vertical installation position of the combustion furnace.

Fig. 5

Device control and interfaces in the device interior

1  Control electronics (behind the cover)
2  Marking interfaces
3  Interface manual boat feeder MBD
4  Interface thermocouple

5 Interface combustion furnace
6 Interface flame sensor (optional, in horizontal

operation with ABD)

Device control, interfaces
in the device

«
...
18
19
20
21
22
...
»

Содержание Analytik Jena Multi X 2500





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Analytik Jena Multi X 2500

Бренд: A&D Страницы: 74

Ultraprobe 9000

Бренд: UE Systems Страницы: 25

ULTRAPROBE 10000

Бренд: UE Systems Страницы: 6

Бренд: YOKOGAWA Страницы: 2

ADMAG TI Series

Бренд: YOKOGAWA Страницы: 8

Comark Diligence 600

Бренд: Fluke Страницы: 61

Бренд: E+E Elektronik Страницы: 32

Бренд: South Страницы: 54

Бренд: Canary Страницы: 19

Pulse sens'O Atex zone 1 50-70-123

Бренд: WATTECO Страницы: 12

Бренд: Warmbier Страницы: 8

CONTOIL VZO Series

Бренд: H. HERMANN EHLERS Страницы: 36

OFL280 FlexTester

Бренд: AFL Страницы: 34

Бренд: Kirby Morgan Страницы: 18

Бренд: SIKA Страницы: 48

Бренд: Rae Страницы: 93

USB-568 RF Series

Бренд: National Instruments Страницы: 8

Бренд: VOLTCRAFT Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды