Endace DAG 5.2X Скачать руководство пользователя

Страница: 48 / 66

EDM01-33v1 DAG_7.5G4_Card_User_Guide

Dagclock

The DUCK is very flexible and can be used with or without an external time reference. It can

accept synchronization from one of several input sources and also be made to drive its

synchronization output from one of several sources.
Synchronization settings are controlled by the

dagclock

utility.

Note:

You should only run

dagclock

after you have loaded the appropriate FPGA images.

If at any stage you reload the FPGA images you must rerun

dagclock

to restore the

configuration.

Note:

when you run

dagconfig -d0 default

the

dagclock

inputs and outputs are also

reset to defaults.

A description of each argument is shown below:

Option

Description

-d DEVICE

--device DEVICE

Use the DAG device referred to by DEVICE. Supported syntax includes 0,

dag1, and /dev/dag3 to refer to DAG cards.

-h, -?

--help, --usage

Display the information on this page

-k

--sync

Wait for DUCK synchronization before exiting

-K NUM

Set the synchronization timeout in seconds (default is 60 seconds)

-l NUM

Set the Health threshold in nanoseconds. (default is 596ns)

-v

Increase output verbosity

-V

Display version information

-x

--clearstats

Clear clock statistics

Command

Description

default

Set the

dagclock

input and output to RS422 in and none out.

none

Clears the input and output settings.

rs422in

Sets the

dagclock

input to RS422.

hostin

Sets the

dagclock

input to Host (unused)

overin

Sets the

dagclock

input to Internal input

auxin

Sets the

dagclock

input to Auxiliary input (unused)

rs422out

Sets the

dagclock

output to repeat the RS422 input signal

loop

Output the selected input

hostout

Sets the

dagclock

output to host (unused)

overout

Internal output (master card)

set

Sets the DAG card's clock to computer clock time and clears clock statistics.

The DAG card takes approximately 20 to 30 seconds to re-synchronize.

reset

Full clock reset. Load time from computer, set RS422in, none out. Clears

clock statistics. The DAG card takes approximately 20 to 30 seconds to re-

synchronize.

Note:

By default, all DAG cards listen for synchronization signals on their RS-422 port,

and do not output any signal to that port.

Содержание DAG 5.2X



































































Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды

Endace DAG 5.2X, Руководство пользователя

Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды