Endace DAG 5.2X Скачать руководство пользователя

Страница: 33 / 66

EDM01-33v1 DAG_7.5G4_Card_User_Guide

Viewing the DAG card status

Interface Status

When you have configured the card according to your specific requirements you can view

the interface statistics to check the status of each of the links using:

dagconfig –d0 –s

(where "0" is the device number of the DAG card you wish to capture data from)
For more information see

dagconfig

(page 28).

There are multiple printout levels. The statistics displayed below are printout level 0.
Example outputs are shown below:

Note:

“

” indicates the condition is present on the link “

0”

indicates the condition is not

present on the link.

Ethernet

Port

pll_lock

lock

los

reset_done

link

lof

A definition of each of the ETHERNET status conditions up to printout level 2 is described

below.

Condition

Description

Link

The link is fully validated.

Lock

Card is locked to the incoming signal and can capture data.

Lof

Loss of frame. Indicates LOF has been asserted for more than 3 secs.

Los

Loss of signal. Indicates there is either no signal at the receiver or the optical

signal strength is too low to be recognized.

peer_link

The peer link is up.

pll_link

Phase Lock Loop locked.

Port

Indicates the port the status conditions apply to.

remote_fault

Remote error indicator.

reset_done

Translater reset finished.

Содержание DAG 5.2X



































































Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды

Endace DAG 5.2X, Руководство пользователя

Результаты поиска

Содержание DAG 5.2X

Отзывы:

Похожие инструкции для DAG 5.2X

Бренды по названию

Популярные бренды