EN 60584
EN 60584
DIN 43710
EN 60584
EN 60584
EN 60584
EN 60584
EN 60584
EN 60584
EN 60751
EN 60751
°C
°F
-199.9...600.0
-30.0....600.0°C
-30.0....600.0°C
-30.0...999.9°C
-30.0...400.0°C
-200...600
-30....600°C
-30....600°C
-30...1300°C
-30....400°C
-40...1700°C
-40...1700°C
°C
°C
-22.0....999.9 °F
-22.0....999.9 °F
-22.0....999.9 °F
-22.0....752.0 °F
-199.9...999.9
-22....2372 °F
-22......752
-40....3092
-40....3092
-328....1112
-22....1112 °F
-22....1112 °F
°F
°F
°F
°F
°F
DIN 43710
ENDA
ET4430
PID
TEMPERATURE
CONTROLLER
Thank you for choosing
ENDA
ET4430
Temperature
C
ontroller
Devices
.
Please read this document carefully before using this product. The guarantee will be invalidated if the device is damaged by not following instructions
detailed in the manual. The company shall not be responsible for any damage or losses however caused, which may be experienced as a result of the
installation or use of this product.
Input Type
Scale Range
J (Fe-CuNi)
Thermocouple
L (Fe-CuNi)
Thermocouple
J (Fe-CuNi)
Thermocouple
L (Fe-CuNi)
Thermocouple
K (NiCr-Ni)
Thermocouple
K (NiCr-Ni)
Thermocouple
T (Cu-CuNi)
Thermocouple
T (Cu-CuNi)
Thermocouple
S (Pt10Rh-Pt) Thermocouple
R (Pt13Rh-Pt) Thermocouple
PT100 Resistance Thermometer
PT100 Resistance Thermometer
0,5% (for full scale)
0,5% (for full scale)
0,5% (for full scale)
0,5% (for full scale)
0,5% (for full scale)
0,5% (for full scale)
1 digit
1 digit
1 digit
1 digit
1 digit
1 digit
0,5% (for full scale)
0,5% (for full scale)
1 digit
1 digit
0,5% (for full scale)
1 digit
0,5% (for full scale)
1 digit
0,2% (
)
for full scale
1 digit
0,2% (
)
for full scale
1 digit
Accuracy
ENVIRONMENTAL CONDITIONS
Height
Ambient/storage temperature
Max. Relative humidity
Rated pollution degree
ELECTRICAL CHARACTERISTICS
Supply
Power consumption
Wiring
Line resistance
Data retention
EMC
Safety requirements
OUTPUTS
A1 Output
Life expectancy for relay
C/A2 Output
SSR Output
C
ONTROL
C
ontrol
type
Control algorithm
A/D
converter
Sampling time
Proportional band
Control period
Hysteresis
Output power
HOUSING
Housing type
Dimensions
Weight
Enclosure material
90-250V AC 50/60Hz,
or 10-30VDC / 8-24VAC
±
%10 SMPS
24V AC ±%10 50/60Hz
Max. 5VA
Power screw-terminal connections: 2.5mm²', Signal screw-terminal connections: 1,5mm².
EN 61326-1: 2013 (Performance criterion B satisfied for EN 61000-4-3 standard).
EEPROM (minimum 10 years)
Max.
100
O
hm
EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)
Suitable for flush-panel mounting according to DIN 43 700.
W48xH48xD87mm
Approx. 250g
Self extinguishing plastics
Single Setpoint and Alarm Control.
On-Off / P, PI, PD, PID selection.
14
bit
.
Min. 1
00ms
.
Can be adjusted between
%0
.0
and
%100
.0 . If
Pb=%0
.0
, ON
-
OFF
c
ontrol
is selected.
Can be adjusted between
1
and 125secs.
Can be adjusted between 1 and 50°C/F.
Setpoint value ratio can be adjusted between %0 and %100 .
Relay : 250V AC, 10A (for resistive load), NO+NC (Control or Alarm2 Output selection).
Relay : 250V AC, 5A (for resistive load), NO (Alarm1 and Cooling Control Output selection).
Max.
2000m
0 ... +50°C/-25 ... +70°C
According to EN 60529; Front panel : IP6
5,
Rear panel : IP20
Max. SSR Output ; 24V 20mA.
Relative humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C.
Without load 30.000.000 switching; 250V AC,
8
A (resistive load) 300.000 switching.
KEEP AWAY device from exposed to corrosive, volatile and flammable gases or liquids and DO NOT USE the device in similar hazardous locations.
Avoid any liquid contact when the device is switched on.
DO NOT clean the device with solvent (thinner, gasoline, acid etc.) and / or abrasive cleaning agents.
Self tune for automatic PID calculation or
manually enter PID parameters if known.
Three different feature assignments for digital input.
Three different feature assignments for the function (F) key.
Soft-Start feature.
SSR or Relay Output Control selection.
A1 Relay output
programmable
as primary Alarm or PID Cooling Control output.
C/A2 Relay output can be used as secondary Alarm or Temperature Control output.
Heating/Cooling control selection.
Zero point input shift
.
In case of sensor failure, periodically, auto-periodically running or relay state can be selected.
RS485 Modbus RTU communication protocol feature (Specify at order).
CE marked according to European Norms.
48x48mm sized.
PT100 ,J, K, L, T, S, R sensor type selections.
Dual setpoint value selection.
Auto calculation for PID parameters (SELF TUNE).
Order Code : ET4430
1
2
1 -
230VAC...90 - 250V AC
24VAC.....24V AC
SM...........10-30V DC /
8-24V AC
Supply Voltage
2
-
RS.....
...
RS485
Blank
....
Modbus (Optional)
Modbus Available
(Optional / Specify at order).
N/A
Please see ET4430 Modbus Address
Map and Connection Diagram Guide for
Modbus feature.
TEMPERATURE CONTROLLER
ET4430
SSR
F
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah.
Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-TURKEY
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr
Barbaros Cad. No:18
1/4