background image

BANDIT III Hardware Description

Page 9

Go to 

Table of 

Contents

Go to 

Top 

Doc

Go to 

List of 

All Docs

1.1.8

Supervisory Port

A Supervisory cable connects the BANDIT III’s DB9 Supervisory port to the DB9 serial port 
of a computer with a control console (such as a PC). 

Note:  

If the Supervisory connection is through a Universal Serial Bus (USB) port on the 

control console computer (such as a personal computer, PC), use an appropriate adapter—
for example, a DB9-to-USB adapter. 

If you wish, you can give the BANDIT III an IP address; then you can configure and monitor 
the BANDIT III over the LAN. This frees the DB9 Supervisory port for use as an additional 
serial port for legacy applications. 

For specifications of the DB9 serial port, see 

Section A.1.1, 

DB9 Supervisory Port

, in 

BANDIT 

III Hardware Specifications

1.1.9

Standard Network Ports 

The following sections discuss the BANDIT products’ port connections to network devices. 

Section 1.1.9.1, 

Ethernet Ports

 

Section 1.1.9.2, 

Modem Port

 

Section 1.1.9.3, 

Serial Port

 

Section 1.1.9.4, 

Wireless Ports

 

Also see 

Section 1.1.10, 

Expansion Ports

Note:  

The BANDIT’s data ports can be configured in the software. The data rates for 

synchronous and asynchronous data ports are shown in 

Table A-10

 an

Table A-11

1.1.9.1

Ethernet Ports 

The BANDIT III has one WAN Ethernet port and three LAN Ethernet ports. The external 
expansion slot can hold an additional Ethernet port. Each 10/100-Base-T Ethernet connection 
is implemented over unshielded twisted-pair (UTP) wire, using a standard RJ45 connector. 

Figure A-3

 shows the RJ45 connector pins. 

Table A-3

 lists the RJ45 pin configuration. 

See the following sections: 

Section 1.1.9.1.1, 

The WAN Ethernet Port

 

Section 1.1.9.1.2, 

The LAN Ethernet Port

 

Section 1.2.1, 

Ethernet DMZ Port for the Expansion Slot

 

1.1.9.1.1

The WAN Ethernet Port

Table 1-2

 lists the WAN port’s interface options. 

Table 1-2. WAN Port Interface Options

Standard

• BANDIT III: 10/100-Base-T, with an RJ45 connector

Top Doc

Doc List

Module TOC

Содержание BANDIT III

















Отзывы: