Enconnex ECX-ER3P-42UXX Скачать руководство пользователя | Manualshive

Страница: 22 / 48

background image

Figure 3-8 Lift the cabinet off the pallet

Step 4

: Remove the cabinet from the pallet and place it in the specified position.

3.3.

Installation

In this section, the installation and commissioning will be explained in detail. Ensure
that all the installation tools and fittings are available prior to installation.

Attention

Following are some safety measures that must be observed prior to installation of the
Edge Rack 3P system:

●

Before installation, ensure that the installation site is clear. The site gradient level
has to be confirmed and should meet the requirements.

●

Switch off the power during installation. Operation on any electrified equipment is
forbidden. The connecting cable must comply with related requirements.

3.3.1.

Installing the cabinet

Following are the steps that need to be observed while installing the cabinet:

Step 1

Measure the height from the ground to the top of the cabinet channel with

a tape measure. By adjusting the leveling feet, make sure the height of the cabinet
is from 2030 mm to 2033 mm.

Step 2

Raise the leveling feet so that the casters touch the ground, Slide the

cabinet into the installation position.

21

«
...
20
21
22
23
24
...
»

Содержание ECX-ER3P-42UXX

















































Отзывы:

Нет отзывов

Похожие инструкции для ECX-ER3P-42UXX

Бренд: Haier Страницы: 2

Бренд: Accucold Страницы: 10

KFZ 45221 A2 NF

Бренд: Koenic Страницы: 116

Бренд: Daewoo Страницы: 15

Бренд: Ariston Страницы: 40

Бренд: Forte Страницы: 10

Бренд: Waeco Страницы: 33

Бренд: Electrolux Страницы: 20

KFN 14842 SD cs-1

Бренд: Miele Страницы: 76

Бренд: Miele Страницы: 72

KFN 29683 D obsw

Бренд: Miele Страницы: 108

Бренд: Miele Страницы: 72

Бренд: Miele Страницы: 56

KFN 14842 SD ed/cs

Бренд: Miele Страницы: 68

Бренд: Miele Страницы: 68

KFN 14943 SD ed

Бренд: Miele Страницы: 64

KFN 14943 SD ed/cs

Бренд: Miele Страницы: 64

KFN 29683 D brws

Бренд: Miele Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды