background image

Users’ Manual 

EAN-26MH Horizontal inclinometer system  

  

  

 

Page

 | 

19

 

7  CALIBRATION CHECK JIG OF INCLINOMETER PROBE 

The calibration check jig is used to ensure that the original factory calibration is unchanged. Any drift in 
inclinometer probe calibration at a later date will be detected by the calibration jig. The calibration jig 
should be fixed to a vertical wall so that at 0

°

 position the calibration jig fixed plate is aligned as much 

horizontal as possible. Before using the probe for taking readings the probe should be inserted in the 
calibration jig and probe readings for 0

°

 and + and - 30

°

 positions are noted down. If any drift is detected 

in the probe readings at a later date, it indicates that the probe needs calibration. It should be noted that 
the 0

°

 and 

±

 30

°

 positions are approximate and should not be taken as calibration points. 

 

Figure 16  shows the calibration jig components. The mounting brackets should be attached to the fixed 
plate of the calibration jig using the supplied set of fasteners. The calibration jig should be fixed to a 
vertical wall surface by fixing the mounting brackets to the wall using any commercially available 
brick/concrete fasteners with 10 mm stud diameter. While fixing ensure that the fixed plate of the 
calibration jig is lengthwise aligned as much horizontal as possible. 

 

Figure 17 shows the index pin and the three reference holes as seen from the back of the calibration jig. 
After installation this side of the jig faces the wall. The index pin is attached to the calibration jig by a 
length of chain. During calibration check the inclinometer guide assembly is rotated till the index pin goes 
through any one of the three holes seen in the figure and the locating hole provided in the guide 
assembly. 
The middle hole corresponds to 0

°

 position and the two holes at either side correspond to + and – 30

°

 

positions. It is immaterial which hole is consve as only the probe readings corresponding to the 
three holes positions are to be noted for future reference. 

 

Figure 16 – Calibration jig components 

Figure 17 – Index pin and reference holes 

Содержание EAN-26MH























Отзывы: