background image

 

 

WiDeFi Inc. 1333 Gateway Drive Suite 1012, Melbourne, Florida 32901 

+1 321.725.1520  

www.WiDeFi.com 

CONFIDENTIAL

 

Radio Frequency Interference Requirements 

Note: This device has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC rules.  These limits are designed to provide reasonable protection 
against harmful interference in a residential installation.  This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications.  However there is no guarantee that 
interference will not occur in a particular installation.  If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following 
measures: 

 

Reorient or relocate the receiving antenna 

 

Increase the separation between the equipment and receiver 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected 

 

Consult the dealer or an experienced radio/TV technician for help 

 

Radio Transmitters (Part 15) 

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following 
two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation. 

 
Class B Equipment 

This equipment has been certified to comply with the limits for a class B computing device 
pursuant to FCC Rules.  In order to maintain compliance with FCC regulations, shielded 
cables must be used with this equipment.  Operation with non-approved equipment or 
unshielded cables is likely to result in interference to radio and TV reception.  

The user is 

cautioned that changes and modifications made to the equipment without the approval of 
the manufacturer could void the user’s authority to operate this equipment. 

FCC Radiation Exposure Statement 

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 
20 cm from all persons and must not be co-located or operating in conjunction with any other 
antenna or transmitter. 

Содержание Xtender














Отзывы: