Empire EMT-7R Скачать руководство пользователя страница 31

3

SPECIFICATIONS

Model 

Number

Usable Oil 

Capacity 

(in

3

)

Rated 

Pressure 

(psi)

Output Flow Rate 

(in

3

/min)

Input Air 

Pressure 

(psi)

Output Port 

Thread

(Oil)

Input Port 

Threads

(Air)

Weight 

(lbs 

w/fluid)

No Load

Load

10,000

110 - 175 3/8” -18NPTF 1/4” - 18NPT

PA1500

91.5

66

11

18.1

• 

Study,  understand,  and  follow  all 

instructions provided with and on this 

device before use.

•  All WARNING statements must be 

carefully  observed  to  help  prevent 

personal injury.

  No alteration shall be made to this 

device.

  Always  wear  protective  gear  when 

operating hydraulic equipment.

  Keep hydraulic equipment away from 

flames and heat. Hydraulic fluid can 

ignite  and  burn.  Do  not  operate  if 

leaks are detected.

• 

Crush Hazard. 

Keep hands and feet 

away from loading area. Avoid pinch 

points  or  crush  points  that  can  be 

created by the load, cylinder, or any 

equipment of system.

• 

To avoid crushing and related injuries:

  NEVER  work  on,  under  or  around 

a  lifted  load  before  it  is  properly 

supported by appropriate mechanical 

means.  Never  rely  on  hydraulic 

pressure alone to support load.

!

   

WARNING

HYDRAULIC PUMPS

•  The  user  must  be  a  qualified  operator  familiar  with  the 

correct operation, maintenance, and use of pumps. Lack of 

knowledge in any of these areas can lead to personal injury.

• Do not exceed rated capacity of the pump or any equipment 

in the system. 

• Never attempt to lift a load weighing more than the capacity 

of the cylinder. 

• Burst hazard exists if hose or connection pressure exceeds 

rated pressure.

• 

Inspect pump, cylinder, hoses and connections before each 

use  to  prevent  unsafe  conditions  from  developing.  Do  not 

use  if  they  are  damaged,  altered  or  in  poor  condition.  Do 

not  operate  the  system  with  bent  or  damaged  coupler  or 

damaged threads.

•  Never  hold  or  stand  directly  in  line  with  any  hydraulic 

connections while pressurizing.

• 

Use gauge or other load measuring instrument to verify load. 

• Never attempt to disconnect hydraulic connections under 

pressure. Release all line pressure before disconnecting 

hoses.

•  Do  not  subject  the  pump  and  its  components  to  shock 

loads.

•  Use only approved accessories and approved hydraulic fluid.

• 

Never attach ANY component not authorized by manufacturer.

•  Always ensure that the chosen application is stable to work 

on and around.

• Do not connect to application  which can return more oil to 

the reservoir than the pump reservoir can hold. 

•  Do  not  connect  pump  to  hydraulic  system  powered  by 

another pump.

•  This device is not suitable for use as support device! As 

the system load is lifted, use blocking and cribbing to guard 

against a falling load.

•  All  personnel  must  be  clear  before  lowering  load  or 

depressurizing the system.

•  Never try to disassemble a hydraulic cylinder, refer repairs 

to qualified, authorized personnel.

HYDRAULIC HOSES & FLUID TRANSMISSION LINES

•  Avoid short runs of straight line tubing. Straight line runs 

do not provide for expansion and contraction due to 

pressure and/or temperature changes.

• Reduce stress in tube lines. Long tubing runs should be 

supported by brackets or clips.  Before operating the pump, 

tighten  all  hose  connections  with  proper  tools.  Do  not 

overtighten. Connections should only be tightened securely 

and leak-free. Overtightening can cause premature thread 

failure or high pressure fittings to burst.

• Should a hydraulic hose ever rupture, burst or need to be 

disconnected, immediately shut off the pump and release 

all pressure. Never attempt to grasp a leaking pressurized 

hose with your hands. The force of escaping hydraulic fluid 

can inflict injury.

• Do not subject the hose to potential hazard such as fire, 

sharp objects, extreme heat or cold, or heavy impact.

•  Do not allow the hose to kink, twist, curl, crush, cut or bend 

so tightly that the fluid flow within the hose is blocked or 

reduced. Periodically inspect the hose for wear.

•  Do not pull, position or move setup by the hose.

•  Hose material and coupler seals must be compatible with 

hydraulic fluid used. Hoses also must not come in contact 

with  corrosive  materials  such  as  battery  acid,  creosote-

impregnated objects and wet paint. Never paint a coupler 

or hose.

• FAILURE TO HEED THESE WARNINGS MAY RESULT IN 

PERSONAL INJURY AS WELL AS PROPERTY DAMAGE.

Содержание EMT-7R















































Отзывы: