Empire DVX36FP31L-4 страница 1 Скачать руководство пользователя

Страница: 1 / 80

LUXURY DIRECT VENT GAS

FIREPLACE HEATER

MILLIVOLT STANDING

PILOT

DIRECT IGNITION

DVX36FP31L(N,P)-4

DVX36FP51LN-2

DVX42FP31L(N,P)-4

DVX42FP51LN-2

INTERMITTENT PILOT

REMOTE RF

DVX36FP71L(N,P)-3

DVX36FP91(N,P)-2

DVX42FP71L(N,P)-3

DVX42FP91(N,P)-2

UL FILE NO. MH30033

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

Direct Vent Zero Clearance Gas

Fireplace Heater

GAS-FIRED

Installer:

Leave this manual with the appliance.

Consumer: Retain this manual for future reference.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by a

qualified installer, service agency or the gas sup

plier.

WARNING: If the information in these instructions

are not followed exactly, a fire or explosion may

result causing property damage, personal injury or

loss of life.

EMPIRE

Comfort Systems

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA only)

or mobile home, where not prohibited by state or local

codes.
This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certified

kit is used.

WARNING: If not installed, operated and maintained

in accordance with the manufacturer’s instructions,

this product could expose you to substances in fuel

or from fuel combustion which can cause death or

serious illness.

Page 1

Содержание DVX36FP31L-4

















































































Результаты поиска

Содержание DVX36FP31L-4

Отзывы:

Похожие инструкции для DVX36FP31L-4

Бренды по названию

Популярные бренды

Empire DVX36FP31L-4, Инструкции по установке и руководства пользователя

Результаты поиска

Содержание DVX36FP31L-4

Отзывы:

Похожие инструкции для DVX36FP31L-4

Бренды по названию

Популярные бренды