Empire Heating Systems RH-25 Скачать руководство пользователя страница 3

12821-8-0907

Page 3

•  Due  to  high  temperatures,  the  room  heater  should  be 

located out of traffic and away from furniture and drap-

eries. 

•  Children and adults should be alerted to the hazards of 

high surface temperature and should stay away to avoid 

burns or clothing ignition.

•  Young children should be carefully supervised when they 

are in the same room as the room heater.

•  Clothing or other flammable material should not be placed 

on or near the room heater.

•  Due to high surface temperatures, keep children, clothing 

and furniture away.  

•  Keep burner and control compartment clean.
•  Installation and repair should be done by a QUALIFIED 

SERVICE PERSON.  The room heater should be inspected 

before use and at least annually by a qualified service 

person.  More frequent cleaning may be required due to 

excessive lint from carpeting, bedding material, etc.  It 

is  imperative  that  control  compartments,  burners  and 

circulating air passageways of the room heater be kept 

clean.

•  DO NOT put anything around the heater that will ob-

struct the flow of combustion and ventilation air.  See 

clearances.

•  DO keep the appliance area clear and free from combus-

tible material, gasoline and other flammable vapors and 

liquids.

•  DO  examine  venting  system  periodically.    Clean  and 

replace damaged parts.  Examinations should be made 

at the start of the heating season and also in mid heating 

season under average conditions.

•  DO  examine  burners  periodically.    Clean  and  replace 

damaged parts.

•  DO NOT use this heater if any part has been under water.  

Immediately call a qualified service technician to inspect 

the heater and to replace any part of  the control system 

and any  gas control which has been under water.

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

Attention: 

During operation of vented room heater the gasket for observation hole cover, observation hole cover and cover plate for 

observation hole cover must be attached to combustion chamber and secured with two (2) wing nuts.

IMPORTANT SAFETY INFORMATION

Содержание RH-25
















Отзывы: