8
9
REMOVING THE DOOR ON THE AL, EM AND EB SERIES
1. Open the door completely
2. Using a small screwdriver flick up the hinge lock A on each hinge
and swing it into the slot.
3. Take the weight of the door and partially close it until there is a
certain resistance. At this point the hinge lock should lock in and
allow the door to be lifted up and away from the cooker.
4. Take care not to damage the hinges - DO NOT force them.
5. When replacing the door repeat the process in reverse order.
Be careful to seat the hinges properly. If the door is crooked and the
hinges seem tight try again.
6. Check that the door is operating properly.
REMOVING THE DOOR ON THE AL, EM AND EB SERIES
1. Open the door completely
2. Using a small screwdriver flick up the hinge lock A on each hinge
and swing it into the slot.
A
3. Take the weight of the door and partially close it until there is a
certain resistance. At this point the hinge lock should lock in and
allow the door to be lifted up and away from the cooker.
4. Take care not to damage the hinges - DO NOT force them.
5. When replacing the door repeat the process in reverse order.
Be careful to seat the hinges properly. If the door is crooked and the
hinges seem tight try again.
6. Check that the door is operating properly.
REMOVING THE DOOR ON THE AL, EM AND EB SERIES
1. Open the door completely
2. Using a small screwdriver flick up the hinge lock A on each hinge
and swing it into the slot.
A
3. Take the weight of the door and partially close it until there is a
certain resistance. At this point the hinge lock should lock in and
allow the door to be lifted up and away from the cooker.
4. Take care not to damage the hinges - DO NOT force them.
5. When replacing the door repeat the process in reverse order.
Be careful to seat the hinges properly. If the door is crooked and the
hinges seem tight try again.
6. Check that the door is operating properly.
DOOR REMOVAL AND RE INSTALLATION
Glem and Emilia cookers have the latest oven door hinge design technology from Glem
Gas. For the removal and re-installation of the oven door with the
new hinges please
follow these procedures:
TO RE-INSTALL THE DOOR
IMPO
RTANT Hold the door at an angle so there is a 150mm gap at the top.
Hook the hinges in first with the groove in the bottom of the hinge sitting on the
roller housing
Once the hinges are located properly fully open the door again
to allow
unlock
ing of
the
hinges and
then you will be able to
close the door.
NOTE - ONCE YOU HAVE INSTALLED THE DOOR IF IT DOES NOT OPEN PROPERLY
REPEAT THE PROCEDURE. DO NOT FORCE THE DOOR AT ANY TIME.
1. Open the door fully.
2. Rotate the hinge locking tab
usingyour finger or a small
screw driver.
3. Tab in locked position. Repeat
the procedure on each hinge.
4. Hold the door as shown.
Close the door until there is a gap
of about 150mm at the top and pull
in the direction of the arrows. The
most pull should be at the lower
part of the door.
Do not force it.
OPEN
150 mm
LIFT UP
PULL
TO RE-INSTALL THE DOOR
NOTE - ONCE YOU HAVE INSTALLED THE DOOR IF IT DOES NOT OPEN PROPERLY REPEAT THE PROCEDURE. DO NOT
FORCE THE DOOR AT ANY TIME.
IMPORTANT Hold the door at an angle so there is a 150mm gap at the top.
Hook the hinges in first with the groove in the bottom of the hinge sitting on the roller housing.
Once the hinges are located properly fully open the door again and unlock the hinges and close the door.
DI/ML SERIES DOOR REMOVAL AND RE INSTALLATION
The DI and ML series of Glem and Emilia cookers have the latest oven door hinge design technology
from Glem Gas. For the removal and re-installation of the oven door with the new hinges please follow
these procedures.
1
2
3
4
5
6
IMPORTANT:
Ensure that the bottom right corner of the inner glass reads VIT.
CLICK AND SLIDE INNER GLASS REMOVAL - SOME MODELS
The models with the click and slide inner glass removal can be identified by the
two
circular press points located towards the top of the inner door. This allows for
easy glass removal to clean the inside of the door.
