Emerson Yarway 7100 Series Скачать руководство пользователя страница 50

Страница: 50 / 60

NetSure

™

-48 VDC Power System

Installation Instructions, IM582127000100 (Revision A, January 9, 2017)

Spec. No: 582127000100, 582127000103

Document Code: IM582127000100

Model No: 7100

Revision A, January 9, 2017

[42]

Figure 27.

Battery Tray Battery Installation Details

Note:

1. Two trays shown as example.

2. Cabling detail omitted.

Connect POS (+)

Battery Cable

to this Terminal

Battery Retention

Bracket. See Detail A

for hardware build-up.

Connect Link Furnished

with Battery to these

Two Terminals

TURN OFF ALL

circuit breakers

before installing

and connecting

any batteries!

Connect NEG (-)

Battery Cable

to this Terminal

Also connect a

provided temperature

probe to this terminal

in each battery tray.

Connect Link Furnished

with Battery to these

Two Terminals

Connect Link Furnished

with Battery to these

Two Terminals

- + - + - + - +

1/4-20 X 5/8” Bolt

1/4” Ground Washer

(1 place)

1/4-20 X 5/8” Bolt

1/4” Lock Washer

1/4” Flat Washer

(3 places)

DETAIL A

Retention Bracket

Hardware Build-Up

StockCheck.com

Содержание Yarway 7100 Series





























































Результаты поиска

Содержание Yarway 7100 Series

Отзывы:

Emerson Yarway 7100 Series, Руководство по установке, Страница: 50 / 60

Результаты поиска

Содержание Yarway 7100 Series

Отзывы: