Emerson unidrive m Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 88

background image

14

SI-Safety Installation & Operating Manual

Issue number: 1

2

Device type

2.1

SI-Safety module

The SI-Safety module is a compact safety controller with integrated drive monitoring for
an axis. This device can be programmed at will to assure safe processing. This
encompasses the EMERGENCY STOP buttons, two-handed operation, light grids,
operating mode selector switches etc., as well as drive-related safety functions. For a
large number of input devices, pre-configured modules are available for safety-related
pre-processing of signals. The same applies to safety functions for drive unit monitoring.
Details can be found in

CTSafePro

help

.

The basic version of this device has safe inputs for a maximum of five input elements
and three disengagement channels.
For 'safe' recording of speed and/or positions, single sensor solutions (Incremental, SIN/
COS, Proxi-Switch) as well as 2-sensor solutions (e.g. Incremental or SSI and
Incremental.) are supported.

Table 2-1 Device version

2.1.1

Module properties

•

Logic processing up to Pl=e in accordance with EN ISO 13849-1 and/or SIL 3 in
accordance with EN 61508

•

Freely programmable small controller for instructions of up to 500 statements

•

Functional plan-oriented programming

•

Impulse outputs for cross-fault detection of digital input signals

•

Safety function, external contact monitoring of connected switchgear

•

Monitored HISIDE outputs for safety-related functions

Device version

Module design with the following peripherals:

2

Sensor interfaces

4 x 2

Grouped safe digital inputs

1 x 1

Safe digital input (monitoring)

2

Impulse outputs

3

HISIDE safe outputs

2

Message outputs

1

Diagnosis and configuration interface

1

Status LED

The SI-Safety module can only be installed in option module slot 3.
The drive only provides power to the SI-Safety module, there are no interface signals
between the module and the drive. The drive will not detect that the module is installed,
and no parameters will be displayed in Menu 17.

NOTE

«
...
12
13
14
15
16
...
»

Содержание unidrive m

























































































Отзывы:

Нет отзывов

Похожие инструкции для unidrive m

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

PXI-6683 Series

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 29

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 7

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 21

FieldPoint FP-1001

Бренд: National Instruments Страницы: 65

FieldPoint FP-1001

Бренд: National Instruments Страницы: 19

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 10

Бренд: Parkside Страницы: 86

Бренд: C&C Страницы: 17

Бренд: DAQ Страницы: 63

Бренд: schmersal Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды