Emerson RXi2-UP Скачать руководство пользователя

Страница: 10 / 66

RXi2-UP IPC Hardware Reference Manual

Section 2

GFK-3047D

Oct 2021

Capability and Compatibility

•

5x Gig Ethernet ports (1 from module plus 4 Ethernet controller (4x i210IT) with
TimeSYNC IEEE1588 and 802.1AS

Alternative 1x GigE and 4x SFP (4x i210IS) (contact Emerson for support)

•

Mini PCIe slot (half and full size)

Unified Infrastructure Management (UIM) interface

•

M.2 PCIe M-Key (PCIe Gen3 x4) and SATA capability

•

M.2 PCIe A-Key (general connectivity)

•

TPM V1.2 or V2.0

•

Up to 4 serial interfaces (2x RS-232, 2x galvanic isolated RS-485/RS-422)

•

Capability for two additional 2.5 inch storage devices with SATA riser board/RAID
option

•

UIM interface

•

0, 1, 2 or 4-slot with active/passive riser board (depending on slot size)

•

Operating at 24 V dc (±25%), including over and under-voltage protection

Figure 6: 2

–

Slot RXi2-UP IPC System Block Diagram

Содержание RXi2-UP



































































Результаты поиска

Содержание RXi2-UP

Отзывы:

Похожие инструкции для RXi2-UP

Бренды по названию

Популярные бренды

Emerson RXi2-UP, Справочник по аппаратуре

Результаты поиска

Содержание RXi2-UP

Отзывы:

Похожие инструкции для RXi2-UP

Бренды по названию

Популярные бренды