Emerson Rosemount Model 500 Скачать руководство пользователя | Manualshive

Страница: 10 / 26

background image

2.2

Installing the carrier shut-off valve and
pressure regulator

This procedure describes installing the carrier shut-off valve as well as installing and
changing the pressure regulator.

Refer to

to perform this task.

Procedure

1. Shut off the carrier and actuation gas supply.
2. Wait until the carrier gas pressure gauge reads zero psi.
3. Disconnect the carrier gas tubing from the tee fitting that is connected to the

carrier gas supply.

WARNING

Do not use hydrogen for valve actuation.

Figure 2-1: Current Carrier Gas Line Configuration Using Helium

A. Pressure switch

B. Tee fitting

C. Carrier gas input

D. Carrier gas line

Installation

Retrofit Instructions

September 2019

SK-07781

10

Emerson.com/Rosemount

«
...
8
9
10
11
12
...
»

Содержание Rosemount Model 500



























Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Model 500

Бренд: Calistair Страницы: 44

Бренд: MachMotion Страницы: 33

Giraffe OmniBed

Бренд: Ohmeda Страницы: 54

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Бренд: GE Страницы: 212

Бренд: Rainin Instrument Страницы: 16

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 39

Бренд: Yamaha Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды