Emerson Rosemount 975HR Скачать руководство пользователя страница 23

Страница: 23 / 80

•

Relays (alarm, fault, auxiliary)

•

RS-485 Modbus

Table 1-6: Available Output Types

Output type

Version

Detector status

Alarm relay

975HR- output configurations
1AXXXXX, 1RXXXXX, and
2RXXXXX

The relay is N.O.

975HR - output configurations
2AXXXXX and 3AXXXXX

The relay is N.O. and N.C.

Auxiliary relay

975HR - output configurations
1AXXXXX, 2AXXXXX, and
1RXXXXX

The relay is N.O.

Fault relay

975HR - output configurations
1AXXXXX, 2AXXXXX, and
1RXXXXX

The relay is N.C. energized.

975HR - output configurations
3AXXXXX and 2RXXXXX

The relay is N.O. energized.

0-20 mA current output

975HR - output configuration
1AXXXXX

Sink with the HART protocol
(can be changed to Source - see

Figure B-3

Figure B-4

, and

Figure B-5

975H - output configurations
2AXXXXX and 3AXXXXXR

Source with the HART protocol

RS-485

All versions

Modbus protocol

1.5.6

Detector status

The possible detector function statuses are listed in the table below. Use HART

Modbus

to see a more detailed fault analysis.

Table 1-7: Detector Statuses

Status

Description

Normal

Normal operation.

BIT

Built-in test being performed.

Warning

Fire detected - changed to

Warning

(pre-alarm state).

Alarm

Fire detected - changed to

Fire Alarm

state.

Latched alarm (optional)

The alarm outputs remain latched on following detection of a fire
that has already been extinguished.

BIT fault

A fault is detected during built-in test sequence or other electric
failure. The detector will continue to detect for fire.

Fault

A fault is detected when the power supply is too low or due to a
software fault or electrical failure. The detector will

not

detect fire

in this condition.

Reference Manual

Introduction

00809-0100-4976

June 2021

Rosemount 975HR

Legacy

Содержание Rosemount 975HR

















































































Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Бренды по названию

Популярные бренды

Emerson Rosemount 975HR, Справочное руководство

Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Бренды по названию

Популярные бренды