Emerson Rosemount 705 Скачать руководство пользователя страница 17

Страница: 17 / 70

Reference Manual

00809-0200-4705, Rev AB

Mounting

May 2017

Mounting

Figure 3-2. Rosemount 705 Terminal Block

A. Pulse input connection
B. HART

terminal connection

C. Terminal block ground connection

3. Attach the transmitter housing to the turbine meter using the threaded conduit entry.

4. Seal threads on 1-in. NPT turbine meter connection. Take union apart and turn on bottom

fitting to turbine meter.

5. Attach mill spec connector to turbine meter pickup.

6. Screw on the remaining union part.

Note

Sealant should already be applied to threads on the D1 (direct mount) option.

Note

Wireless devices should only be powered up after the Smart Wireless Gateway, in order of
proximity from the Smart Wireless Gateway beginning with the closest device. This results in a
simpler and faster network installation.

7. Connect the black power module

Figure 3-3. Power Module Installation

8. Close the housing cover and tighten to safety specification. Always ensure a proper seal so

metal touches metal, but do not over tighten.

9. Position the antenna so it is vertical, either straight up or straight down.

a. The antenna should be approximately 3 ft. (0.91 m) from any large structures or

buildings, to allow clear communication to other devices.

Содержание Rosemount 705







































































Результаты поиска

Содержание Rosemount 705

Отзывы:

Похожие инструкции для Rosemount 705

Бренды по названию

Популярные бренды

Emerson Rosemount 705, Справочное руководство

Результаты поиска

Содержание Rosemount 705

Отзывы:

Похожие инструкции для Rosemount 705

Бренды по названию

Популярные бренды