manualshive.com logo in svg

Emerson Rosemount 644 FOUNDATION, Справочное руководство

Поделиться
Скачать
Emerson Rosemount 644 FOUNDATION Скачать руководство пользователя страница 14

8

Reference Manual

00809-0400-4728, Rev CA

Configuration

September 2018

Configuration

2.3.6

Capabilities

Virtual Communication Relationship (VCR) 

There are a total of 12 VCR’s. One is permanent and 11 are fully configurable by the host system. 16 link 
objects are available.

Block execution times

Analog input = 45 ms
PID = 60 ms

2.3.7

Surges/transients

The transmitter will withstand electrical transients of the energy level encountered in static discharges or 
induced switching transients. However, high-energy transients, such as those induced in wiring from 
nearby lightning strikes, welding, heavy electrical equipment, or switching gears, can damage both the 
transmitter and the sensor. To protect against high-energy transients, install the transmitter into a 
suitable connection head with the integral transient protector, option T1. Refer to the Rosemount 644 
Product Data Sheet for more information.

2.4

F

OUNDATION

 Fieldbus function blocks 

For reference information on the Resource, Sensor Transducer, AI, LCD Transducer blocks refer to 
F

OUNDATION

 Fieldbus Block Information on 

page 41

. Reference information on the PID block can be found 

in the Function Block 

Reference Manual

.

Resource block (index number 1000)

The Resource Function Block (RB) contains diagnostic, hardware, and electronics information. There are 
no linkable inputs or outputs to the Resource Block.

Sensor transducer block (index number 1100)

The Sensor Transducer Function Block (STB) temperature measurement data includes sensor and 
terminal temperature. The STB also includes information about sensor type, engineering units, 
linearization, reranging, damping, temperature compensation, and diagnostics.

Network parameter

Value

Slot Time

8

Maximum Response Delay

2

Maximum Inactivity to Claim LAS Delay

32

Minimum Inter DLPDU Delay

8

Time Sync class

4 (1ms)

Maximum Scheduling Overhead

21

Per CLPDU PhL Overhead

4

Maximum Inter-channel Signal Skew

0

Required Number of Post-transmission-gab-ext Units

0

Required Number of Preamble-extension Units

1

Содержание Rosemount 644 FOUNDATION

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды