Emerson Rosemount 3812 Скачать руководство пользователя страница 99

Страница: 99 / 132

AMS

™

Device Manager or a HART

Field Communicator and select

Overview

→

Zero Calibration

→

Start

menu or

Service Tools

→

Maintenance

→

Zero

Calibration

→

Start

15. Close your application connection (MeterLink, AMS

™

Device Manager or HART

Field Communicator).

16. If replacing other electronics, continue with the following procedures before

replacing the end caps and sealing the enclosure.

17. If you are not replacing other electronics, replace the end caps and security latches

(3 mm Allen wrench required). If required, install the security seals (see

Seal the

Junction Box for remote mount electronics option

18. Apply power to the meter.

This completes the I.S. Barrier Board replacement procedure.

If you encounter problems with this procedure, see the Emerson Customer Support
contact information on the back cover of this manual.

3.9.5

Replace the Power Supply Board

Procedure

1. If replacing the Power Supply board, disable electrical power to the meter.
2. Refer to

Table 3-9

for the tools required to complete this procedure.

3. Disconnect the Transmitter Electronics Enclosure security seals, loosen the end cap

security latches with a 3mm Allen wrench and remove both end caps.

4. Use a 1/8 inch (3 mm) flat head screw driver and remove the terminal blocks from

the Power Supply board, the CPU Module and the Optional I/O Module. See

Figure

3-57

for board locations and associated terminal blocks.

5. Use a #1 Standard Phillips head screw driver and remove the four Backplane board

screws from the enclosure standoffs.

Maintenance and Troubleshooting Manual

Meter maintenance

00809-0100-3812

April 2022

Rosemount 3812 Liquid Ultrasonic Flow Meter

Содержание Rosemount 3812





































































































































Результаты поиска

Содержание Rosemount 3812

Отзывы:

Похожие инструкции для Rosemount 3812

Бренды по названию

Популярные бренды

Emerson Rosemount 3812, Руководство по техническому обслуживанию и устранению неисправностей

Результаты поиска

Содержание Rosemount 3812

Отзывы:

Похожие инструкции для Rosemount 3812

Бренды по названию

Популярные бренды