Emerson Rosemount 3812 Скачать руководство пользователя страница 44

Страница: 44 / 132

Figure 3-5: Bolted band shroud meter assembly - bottom view

A. 5/16”-18UNC bolts and lock washers

Procedure

1. Use the 1/2 wrench to loosen and remove one of the bolted band shroud bolts and

lock washer while holding the band shroud to prevent spring back of the shroud.

2. Loosen and remove the second bolted band shroud bolt with lock washer using the

1/2" wrench.

3. Spread the band shroud apart and remove from the body and place the circular

edge on a flat surface.

4. Use the 1/2" wrench and remove the two end shroud bolts with lock washers while

holding the end shrouds in position. As the bolts are loosened, remove both end
shrouds and place on a flat surface.

5. Repeat Steps 1 through 4 to remove the other band shroud.
6. Move the shroud parts, bolts and lock washers out of your immediate work area.

This completes the bolted band shroud removal procedure.

3.4.2

Remove clamped band shrouds

WARNING

CUTTING HAZARD
Sharp edges may be present on the band shrouds.
Wear appropriate personal protective equipment when working on the meter.
Failure to comply may cause serious injury.

Table 3-3: Clamped band shroud removal tool list

Tools required

Standard

inch socket or a standard

inch wrench

Flat blade screw driver or 5/16 inch nut driver

Appropriate personal protective equipment

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

Emerson.com/Rosemount

Содержание Rosemount 3812





































































































































Результаты поиска

Содержание Rosemount 3812

Отзывы:

Похожие инструкции для Rosemount 3812

Бренды по названию

Популярные бренды

Emerson Rosemount 3812, Руководство по техническому обслуживанию и устранению неисправностей

Результаты поиска

Содержание Rosemount 3812

Отзывы:

Похожие инструкции для Rosemount 3812

Бренды по названию

Популярные бренды