Emerson Rosemount 3144P Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 236

Emerson Rosemount 3144P Скачать руководство пользователя страница 154

144

Reference Manual

00809-0100-4021, Rev JA

Configuration

April 2017

Configuration

Table 4-4. Resource Block RB.FD_EXTENDED_ACTIVE

4.6

Sensor transducer block

Note

When the engineering units of the XD_SCALE in the associated AI Block are selected, the engineering
units in the transducer block change to the same units.
This is the only way to change the engineering units in the sensor transducer block.

Damping

Damping values may be used for, and should equal, the update rate for Sensor 1, Sensor 2, and sensor
differential. Sensor configuration automatically calculates a damping value. The default damping value is
5 seconds. Damping may be disabled by setting the parameter damping value to 0 seconds. The
maximum damping value allowed is 32 seconds.

An alternate damping value may be entered with the following restrictions.

1. Single sensor configuration

–

50 or 60 Hz line voltage filters have a minimum user-configurable damping value of 0.5 seconds.

2. Dual sensor configuration

–

50 Hz line voltage filter a minimum user-configurable damping value of 0.9 seconds.

–

60 Hz line voltage filter a minimum user-configurable damping value of 0.7 seconds.

The damping parameter in the transducer block may be used to filter measurement noise. By increasing
the damping time, the transmitter will have a slower response time, but will decrease the amount of
process noise that is translated to the transducer block primary value. Because both the LCD display and
AI Block get input from the transducer block, adjusting the damping parameter affects the values passed
to both blocks.

Note

The AI block has a filtering parameter called PV_FTIME. For simplicity, it is better to do filtering in the
transducer block as damping will be applied to primary value on every sensor update. If filtering is done
in AI block, damping will be applied to output every macrocycle. The LCD display will display value from
transducer block.

RB.DETAILED_STATUS

Description

Sensor Transducer block error

Active when any SENSOR_DETAILED_STATUS bit is on

Manufacturing Block integrity error

The manufacturing block size, revision, or checksum is wrong

Hardware/software incompatible

Verify the manufacturing block revision and the hardware revision are

correct/compatible with the software revision

Non-volatile memory integrity error

Invalid checksum on a block of NV data

ROM integrity error

Invalid application code checksum

«
...
152
153
154
155
156
...
»

Содержание Rosemount 3144P













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды