manualshive.com logo in svg

Emerson Rosemount 2240S, Справочное руководство, Страница: 48 / 194

Поделиться
Скачать
Emerson Rosemount 2240S Скачать руководство пользователя страница 48

38

Reference Manual

00809-0100-2240, Rev DA

Rosemount

™

 2240S Installation

October 2017

Rosemount

™

 2240S Installation

4.4.7

Typical installations

The example below (

Figure 4-3

) illustrates a system with daisy-chained field devices on a single tank. 

Terminators are installed at both ends of the Tankbus segment as required in a system that complies with 
the F

OUNDATION

 fieldbus standard. In this case terminators are enabled in the Rosemount 2410 Tank Hub 

and a field device at the end of the network segment. 

In addition to the field instruments on the Tankbus, 

Figure 4-3

 illustrates how an instrument such as a 

pressure transmitter can be connected to the intrinsically safe 4 -20 mA analog input of the Rosemount 
2410 Tank Hub.

Figure 4-3. Example of a Tankbus Connection for a Single Tank

The maximum distance between the Rosemount 2410 Tank Hub and the field devices on the tank 
depends on the number of devices connected to the Tankbus and the quality of cables. 

See chapter “Electrical Installation” in the 

Rosemount 2410 Reference Manual

 for more information 

about cable selection, power budget, and the Tankbus.

See chapter “Typical Installations” in the 

Rosemount 2410 Reference Manual

 for more examples of how 

to install systems that include the Rosemount 2410 Tank Hub.

Rosemount 5900S 
Radar Level Gauge

Rosemount 2240S Multi-input 
Temperature Transmitter

Built-in 
terminator 
enabled on the 
last device

Rosemount 2230 
Display

Rosemount 2410 Tank Hub with 
intrinsically safe power supply, 
integrated power conditioner, and 
built-in terminator

Tankbus length up to 1000 meter depending on 
number of devices and cable type

Tankbus

IS Analog Input 
(Secondary bus)

Rosemount 3051S 
Pressure Transmitter

Maximum number of HART Slave Devices
Passive current loop: 5
Active current loop: 3

Содержание Rosemount 2240S



































































































































































































Отзывы:

Нет отзывов