manualshive.com logo in svg

Emerson Rosemount 2240S, Справочное руководство, Страница: 47 / 194

Поделиться
Скачать
Emerson Rosemount 2240S Скачать руководство пользователя страница 47

37

Reference Manual 

00809-0100-2240, Rev DA

Rosemount

™

 2240S Installation

October 2017

Rosemount

™

 2240S Installation

4.4.6

The Tankbus

The Rosemount Tank Gauging system is easy to install and wire. Field devices can be “daisy-chained” thus 
reducing the number of external junction boxes. Devices communicate with a Rosemount 2410 Tank 
Hub via the intrinsically safe Tankbus that complies with the FISCO

(1)

 F

OUNDATION

 fieldbus standard. The 

Rosemount 2410 acts as power supply to the field devices on the Tankbus. A FISCO system enables more 
field devices to be connected to the segment compared to conventional I.S. systems based on the entity 
concept.

Termination 

A terminator is needed at each end of a F

OUNDATION

 fieldbus network. Generally, one terminator is placed 

at the fieldbus power supply, and the other one at the last device in the fieldbus network. 

Note

Ensure there are 

two

 terminators on the Tankbus, see 

Figure 4-3

.

In a Rosemount Tank Gauging system the Rosemount 2410 Tank Hub acts as power supply. Since the tank 
hub normally is the first device in the fieldbus segment, the built-in termination is enabled at factory.

Devices such as the standard version of the Rosemount 5900S Radar Level Gauge, the Rosemount 2230 
Graphical Field Display, and the Rosemount 2240S Multi-input Temperature Transmitter also have 
built-in terminators which can easily be enabled by inserting a jumper in the terminal block when 
necessary. 

If the Rosemount 2240S is not the last device in the fieldbus network, disconnect the termination 
jumper. See 

Figure 4-6 on page 41

.

Segment design

When designing a FISCO fieldbus segment a few requirements need to be considered. Cabling has to 
comply with FISCO requirements as described in 

“Cable selection” on page 35

. You will also have to 

ensure that the total operating current of the connected field devices is within the output capability of 
the Rosemount 2410 Tank Hub. The tank hub is able to deliver 250 mA. In a Smart Wireless System the 
maximum current is 200 mA. Consequently, the number of field devices has to be considered so that the 
total current consumption is less than the available current. See section “Power Budget” in the 

Rosemount 2410 Reference Manual

 for more information.

Another requirement is to ensure that the input voltage at the field device terminals is at least 9 V. 
Therefore, the voltage drop in the fieldbus cables has to be taken into account. 

Distances are normally quite short between the Rosemount 2410 Tank Hub and field devices on the 
tank. In many cases you can use existing cables as long as the FISCO requirements are fulfilled (see 

“Cable 

selection” on page 35

).

See the 

Rosemount 2410 Reference Manual

 for more information on segment design of a Rosemount 

Tank Gauging system.

1, 

FISCO=Fieldbus Intrinsically Safe Concept

Содержание Rosemount 2240S



































































































































































































Отзывы:

Нет отзывов