Emerson Rosemount 2051 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 228

background image

66

Reference Manual

00809-0100-4107, Rev BA

Section 5: Operation and Maintenance

April 2013

Operation and Maintenance

5.3

Recommended calibration tasks

Table 5-1. Basic and full calibration tasks

Note

For Rosemount 2051CA, Rosemount 2051TA range 0 and range 5 devices, an accurate absolute
pressure source is required.

5.4

Calibration overview

The Rosemount 2051 pressure transmitter is an accurate instrument that is fully calibrated in
the factory. Field calibration is provided to the user to meet plant requirements or industry
standards. Complete calibration of the Rosemount 2051 can be split into two halves: Sensor
Calibration and Analog Output Calibration.

Sensor Calibration allows the user to adjust the pressure (digital value) reported by the
transmitter to be equal to a pressure standard. The Sensor Calibration can adjust the pressure
offset to correct for mounting conditions or line pressure effects. This correction is
recommended. The calibration of the pressure range (pressure span or gain correction)
requires accurate pressure standards (sources) to provide a full calibration.

Like the Sensor Calibration, the analog output can be calibrated to match the user measurement
system. The Analog Output Trim (4-20mA/ 1-5 VOutput Trim) will calibrate the loop at the
4mA (1 V) and 20mA (5 V) points.

Absolute pressure transmitters (Rosemount 2051CA and Rosemount 2051TA) are
calibrated at the factory. Trimming adjusts the position of the factory characterization
curve. It is possible to degrade performance of the transmitter if any trim is done
improperly or with inaccurate equipment.

Field installation tasks

Bench calibration tasks

1.

Perform Sensor zero/lower Trim:

Compensate for mounting pressure
effects

a.

Refer to

for manifold

operation instructions to properly
drain/vent valves

2.

Set/check basic configuration

parameters

a.

Output units

b.

Range points

c.

Output type

d.

Damping Value

1.

Perform optional 4-20mA 1-5 Vdc

Output Trim

2.

Perform a Sensor Trim

a.

Zero/lower trim using line

pressure effect correction.
Reference

manifold drain/vent valve
operation instructions.

b.

Optional full scale trim. Sets the

span of the device and requires
accurate calibration equipment

c.

Set/check basic configuration

parameters.

«
...
74
75
76
77
78
...
»

Содержание Rosemount 2051





































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 2051

NUFLO Scanner 2000 microEFM

Бренд: Cameron Страницы: 8

HX3 Drawbar Expander Version 5

Бренд: KEYBOARDPARTNER Страницы: 11

Бренд: DAKOTA ULTRASONICS Страницы: 51

ColorTrack Genesis

Бренд: Fresh Roast Systems Страницы: 9

Бренд: Skil Страницы: 80

Бренд: Kurzweil Страницы: 35

Cobra SMARTsense Chloride Ion

Бренд: PHYWE Страницы: 4

LASERSCALE BL55-RU Series

Бренд: Magnescale Страницы: 40

Бренд: Oakton Страницы: 12

Бренд: KAM Страницы: 4

Бренд: BERTHOLD TECHNOLOGIES Страницы: 127

CONTOIL VZO Series

Бренд: H. HERMANN EHLERS Страницы: 36

Бренд: ICP DAS USA Страницы: 8

Бренд: AEMC Страницы: 64

Бренд: Major tech Страницы: 2

Бренд: Megger Страницы: 2

Cobra4 Sensor-Unit Weather

Бренд: PHYWE Страницы: 3

DataLoop LI23 Series

Бренд: FlowLine Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды