Quantum MP User Guide
65
Issue: A4 www.emersonct.com
* Modes 1 and 2 are not user saved, Modes 0, 3 and 4 are user saved.
** Only applicable to Modbus RTU mode.
Key:
6.1 Full descriptions
6.1.1 Parameter x.00
Caution should be taken before writing to SMARTCARD data block 200
or before performing 9999 Erase SMARTCARD. Proceeding will
overwrite or erase the Quantum MP default parameter values stored in
SMARTCARD data block 200.
Pr
x.00
is available in all menus and has the following functions.
information of these functions.
** These functions do not require a drive reset to become active. All
other functions require a drive reset to initiate the function.
Fb09
Drive encoder speed feedback
{0.79, 3.27}
±10,000.0 rpm
RW
Bi
FI NC PT US
in01
Analog input 3 mode
{0.81, 7.15}
0-20 (0), 20-0 (1), 4-20.tr (2), 20-4.tr (3), 4-20
(4), 20-4 (5), VOLt (6), th.SC (7), th (8), th.
diSp (9)
th(8)
RW Txt
US
in02
Analog input 1
{0.82, 7.01}
±100.00%
RO
Bi
NC PT
in03
Analog input 2
{0.83, 7.02}
±100.0%
RO
Bi
NC PT
in04
Analog input 3
{0.84, 7.03}
±100.0%
RO
Bi
NC PT
in05
T24 digital I/O 1 state
{0.85, 8.01}
OFF (0) or On (1)
RO
Bit
NC PT
in06
T25 digital I/O 2 state
{0.86, 8.02}
RO
Bit
NC PT
in07
T26 digital I/O 3 state
{0.87, 8.03}
RO
Bit
NC PT
in08
T27 digital input 4 state
{0.88, 8.04}
RO
Bit
NC PT
in09
T28 digital input 5 state
{0.89, 8.05}
RO
Bit
NC PT
in10
T29 digital input 6 state
{0.90, 8.06}
RO
Bit
NC PT
Parameter
Range(
)
Default(
)
Type
Coding
Attribute
{X.XX}
Copied Menu 0 or advanced parameter
RW
Read/write: can be written by the user
RO
Read only: can only be read by the user
Bit
1 bit parameter: ‘On’ or ‘OFF’ on the display
Bi
Bipolar parameter
Uni
Unipolar parameter
Txt
Text: the parameter uses text strings instead of numbers.
FI
Filtered: some parameters which can have rapidly changing
values are filtered when displayed on the drive keypad for
easy viewing.
DE
Destination: This parameter selects the destination of an
input or logic function.
RA
Rating dependent: this parameter is likely to have different
values and ranges with drives of different voltage and
current ratings. Parameters with this attribute will not be
transferred to the destination drive by SMARTCARDs when
the rating of the destination drive is different from the
source drive and the file is a parameter file. However, the
value will be transferred if only the current rating is different
and the file is a differences from default type file.
NC
Not copied: not transferred to or from SMARTCARDs
during copying.
PT
Protected: cannot be used as a destination.
US
User save: parameter saved in drive EEPROM when the
user initiates a parameter save.
PS
Power-down save: parameter automatically saved in drive
EEPROM when the under volts (UV) trip occurs. Power-
down save parameters are also saved in the drive when the
user initiates a parameter save.
SE00 {x.00}
Parameter zero
RW
Uni
0 to 32,767
0
Value
String
Action
0
No Act
No action
1
SAUE
Save parameters
2
rEAd 1*
Transfer SMART card data block 1 to the drive
3
PrOg 1*
Transfer drive parameters as difference from
default to SMART card block number 1
4
rEAd 2*
Transfer SMART card data block 2 to the drive
5
PrOg 2*
Transfer drive parameters as difference from
default to SMART card block number 2
6
rEAd 3*
Transfer SMART card data block 3 to the drive
7
PrOg 3*
Transfer drive parameters as difference from
default to SMART card block number 3
8
diS.diFF
Display non-default values only
9
diS.dESt
Display destination parameters only
10
Eur
Load European defaults
11
USA
Load USA defaults
12
rES OP
Reset all Solution Modules
1000
1000
Save parameters
1070
1070
Reset all Solution Modules
1233
1233
Load European defaults
1244
1244
Load USA defaults
1255
1255
Load European defaults (excluding menus 15 to 20)
1256
1256
Load USA defaults (excluding menus 15 to 20)
2001
2001*
Transfer drive parameter to a card and create a
bootable difference from default SMART card block
with data block number 1 and clear parameter
11.42. If data block 1 exists it is over written.
3yyy
3yyy*
Transfer drive parameters to SMART card block
number yyy
4yyy
4yyy*
Transfer drive parameters as difference from
default to SMART card block number yyy
5yyy
5yyy*
Transfer Onboard Applications Lite ladder
program to SMART card block number yyy
6yyy
6yyy*
Transfer SMART card data block yyy to the drive
6200
6200*
Transfer Quantum MP defaults from
SMARTCARD data block 200 to the drive
7yyy
7yyy*
Erase SMART card data block yyy
8yyy
8yyy*
Compare drive data with SMART card block yyy
9555
9555*
Clear SMART card warning suppression flag
9666
9666*
Set SMART card warning suppression flag
9777
9777*
Clear SMART card read-only flag
9888
9888*
Set SMART card read-only flag
9999
9999*
Erase SMART card
12000**
12000**
Display non-default values only
12001**
12001**
Display destination parameters only
