manualshive.com logo in svg

Emerson PACSystems Versamax, Руководство пользователя

Поделиться
Скачать
Emerson PACSystems Versamax Скачать руководство пользователя страница 45

User Manual 

Chapter 4 

GFK-2721B 

Sep 2019 

 

Diagnostics 

 

 

 

 

 

 

                            41 

 

 
 

Channel 

Error 

Type 

Diagnosis 

Alarm 

Type 

Module 

or 

Channel 

Error 

Cause 

Fault Text 

Recommendation 

mode on an 
ALG240 
with < 2mA 
input 

-Verify output is 
within range 
(remove shorts) 

259 

Channel 
Diagnosis 
Appears / 
Disappears 

Module 

Nonvolatile 
Store Fault. 

Non-Volatile 
Store Failed 

There are no 
corrective actions for 
this. Try store again 
or fix hardware. 

260 

Channel 
Diagnosis 
Appears / 
Disappears 

Channel 

Wiring Fault. 
RTD 
measurement
s 
are such that 
wiring 
problems are 
suspected 

Wiring Fault 

Verify RTD wiring 
and configuration. 

261 

Channel 
Diagnosis 
Appears / 
Disappears 

Module 

Thermistor 
fault. 
The 
thermistor in 
the 
thermocouple 
carrier is out 
of range 

Thermistor 
Fault 

Verify the 
thermocouple 
carrier. 

768 

Channel 
Diagnosis 

Channel 

A PROFIBUS 
slave is not 
connected to 
IC200BEM003 
PROFIBUS DP 
Master 
module 

Loss of 

Check PROFIBUS DB-
9 connector and 
cable on 
IC200BEM003 
module and the 
slave. 
or, 
Wait for a time when 
the PROFIBUS data 
rate is set very low. 

4.2.3

 

Clearing Faults on VersaMax Analog Modules 

The VersaMax PROFINET Scanner clears alarms as soon as the underlying condition returns 
to normal. 

For some VersaMax modules such as the IC200ALG240, IC200ALG331, IC200ALG620, and 
IC200ALG630, the VersaMax PROFINET Scanner automatically checks every five seconds to 
see  whether  a  module  error  condition  is  still  present.  When  these  modules  are  checked 
periodically, a historical log of alarms such as the IO Fault log in PAC Machine Edition may 
show  new  alarms  occurring  before  previous  alarms  clear.  For  example,  if  field  power  is 

Содержание PACSystems Versamax






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды