Emerson Liebert NXL 250 kVA Скачать руководство пользователя

Страница: 41 / 112

Operation

Liebert

NXL

™

9. Close all Battery/DC breakers associated with this module. The UPS will stay in this mode until

all breakers are closed.
Skip this command if the DC sources are not ready to be started. The DC breakers can be closed

later from the startup command (see

2.5 - Startup Menu

The UPS is ready to be placed online. Go to the SCC Startup screen to complete the startup.

2.15.3 Startup—1+N System

This section lists typical step-by-step instructions. The touchscreen will list all steps required for the

process, based on the unit’s condition and other factors.

NOTICE

Risk of equipment damage. If an abnormal situation occurs during this startup procedure, open

the input circuit breaker and investigate the problem. Call Liebert Services if help is needed.

NOTE

The DC source charge current may increase quickly, but should slowly decrease. If the system is

recovering from a DC source shutdown or an input power failure, the UPS rectifier will be

recharging the battery. Recharge current can be more than 100A. The maximum allowable

recharge current for a unit depends on the kVA rating and the DC source recharge current limit.

WARNING

Risk of electrical shock and high short circuit current. Can cause equipment damage, personal

injury and death.
If the UPS has been shut down for maintenance, verify that all of the UPS system doors are

closed and latched. All test equipment must be removed from the system. All electrical

connections must be secure.

WARNING

Risk of electrical shock. Can cause equipment damage, personal injury and death.
The following procedure may provide power to the critical load distribution system. Verify

that the critical load distribution is ready to accept power. Make sure that personnel and

equipment are ready for the critical load distribution system to be energized.

NOTE

If the system was shut down in response to an “Emergency Off,” there may be alarm messages

on the touchscreen that describe system conditions before or at the time of the shutdown. Some

or all of the alarm conditions may have been resolved.
To clear these alarm messages, turn Off control power (see

Figures 2

and

). Wait at least

10 minutes for the control power circuitry to completely de-energize. After 10 minutes, turn

control power back On.

Содержание Liebert NXL 250 kVA

















































































































Результаты поиска

Содержание Liebert NXL 250 kVA

Отзывы:

Похожие инструкции для Liebert NXL 250 kVA

Бренды по названию

Популярные бренды

Emerson Liebert NXL 250 kVA, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Liebert NXL 250 kVA

Отзывы:

Похожие инструкции для Liebert NXL 250 kVA

Бренды по названию

Популярные бренды