Emerson Liebert eXL Скачать руководство пользователя

Страница: 29 / 40

Specifications

Liebert

™

Minimum Clearance, Sides, in (mm)

Location of Cable Entrance

Top or Bottom

Standards and Conformities

UL 1778, 4th Ed.

CSA 22.2 107.3

FCC Part 15, Class A (with optional filters installed)

IEC62040-2, Level 4, Criteria A

ANSI C62.41, Category A3 &B3

ISTA

WEEE

Environmental Parameters

Storage Temperature Range, °F (°C)

-13 to 158 (-25 to 70)

Operating Temperature Range, °F (°C)

32°F to 95°F (0°C to 35°C) at full rated load

1.5% maximum kW / degrees C derating up to 50°C

122°F (50°C) absolute maximum with derating

Relative Humidity

95% or less Non-Condensing

(Operating and Non-Operating)

Maximum Altitude Above MSL

3300 ft.(1000m) (per IEC 62040/3) - 1% Maximum kW

derating / 1000 ft. rise between 3300 and 10,000 ft.(305m

rise between 1000 and 3000m)

Width dimensions are with side panels attached. Subtract 1.4" (35mm) for dimensions without side panels.
Depth dimensions include the front door and rear panel.

Table 8

Current ratings—rectifier input

UPS Rating

Voltage

VAC

Nominal

Current

Maximum

Current

kVA

625

480

779

818

750

480

935

982

800

480

995

1044

Table 9

Current ratings—bypass input

UPS Rating

Voltage

VAC

Nominal

Current

kVA

625

480

752

750

480

902

800

480

962

Table 10

Current ratings—output

UPS Rating

Voltage

VAC

Nominal

Current

kVA

625

480

752

750

480

902

800

480

962

Table 11

Current ratings—DC source

UPS Rating

Voltage

VAC

Nominal

Current

Notes on Tables

kVA

1. Nominal rectifier AC input current (considered

625

480

1624

continuous) is based on full rated output load. Maximum current

includes nominal input current and maximum battery recharge

current (considered non-continuous).

2. The rectifier overload current is controlled by the input current limit

setting, which is adjustable from 25 to 200% (default:125%).

3. For breaker coordination while the module is overloaded, see the

current versus time values on the overload curves.

4. Nominal battery voltage is shown at 2.0 volts/cell.

5. DC Source current based at 401VDC.

750

480

1949

800

480

2079

Table 7

Liebert

XL UPS specifications

(continued)

Model Size

625-800kVA

Содержание Liebert eXL









































Результаты поиска

Содержание Liebert eXL

Отзывы:

Похожие инструкции для Liebert eXL

Бренды по названию

Популярные бренды

Emerson Liebert eXL, Руководство по установке

Результаты поиска

Содержание Liebert eXL

Отзывы:

Похожие инструкции для Liebert eXL

Бренды по названию

Популярные бренды