Emerson Liebert APM 120 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 144

background image

Installation

9

Liebert

®

APM

™

2.1

Initial Inspections

1. While the Liebert APM and ancillary cabinets are still on the truck, inspect the equipment and

shipping container for any signs of damage or mishandling. Do not attempt to install the system if

damage is apparent. If any damage is noted, file a damage claim with the shipping agency

immediately and contact Liebert Services at 1-800-LIEBERT to inform them of the damage claim

and the condition of the equipment.

2. Compare the contents of the shipment with the bill of lading. Report any missing items to the

carrier and your local Emerson representative immediately.

3. Check the product label on the back of front door and confirm the contents match the UPS model,

capacity and main parameters that were ordered.

2.1.1 Storing for Delayed Installation

If the equipment will not be installed immediately, it must be stored indoors where the humidity is no

higher than 90% and the temperature is no higher than 104°F (40°C). The storage area must protect

the Liebert APM from excessive moisture (see

11.2 - UPS Environmental

2.2

Preliminary Checks

2.2.1 Identification

The equipment supplied has an identification tag on the back of the main door listing the type and

size of the UPS.

2.3

UPS Location

2.3.1 Positioning the UPS

Choose a location for the UPS that offers:

• Easy connection to inputs, outputs and auxiliary equipment
• Enough space to service the UPS
• Air circulation sufficient to expel heat produced by UPS
• Protection against moisture and excessive humidity
• Protection against dust and other particulate matter
• Compliance with fire prevention regulations and practices
• Operating environment temperature of 74-80°F (23-27°C) for maximum battery efficiency

!

CAUTION

If the UPS must remain disconnected from power for more than six (6) months, the batteries

(if so equipped) must be recharged before use. To charge the batteries, the unit must be

connected to utility power and started up—the charger operates only while the Liebert APM

is operating.

!

CAUTION

When batteries are installed in the UPS or are cabinet-mounted adjacent to the UPS, the

battery—not the UPS—dictates the designed maximum ambient temperature.

«
...
17
18
19
20
21
...
»

Содержание Liebert APM 120

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Liebert APM 120

Бренд: Eaton Страницы: 20

Бренд: Panamax Страницы: 2

Бренд: Emerson Страницы: 7

Бренд: Emerson Страницы: 26

Liebert GXT MT+LB 10K

Бренд: Emerson Страницы: 30

Бренд: Emerson Страницы: 32

Бренд: Emerson Страницы: 40

Бренд: Emerson Страницы: 16

Бренд: Emerson Страницы: 33

Бренд: Emerson Страницы: 27

Бренд: Emerson Страницы: 50

Liebert GXT2-10000RT208

Бренд: Emerson Страницы: 56

Бренд: Emerson Страницы: 67

Бренд: Emerson Страницы: 46

Бренд: Emerson Страницы: 92

Бренд: Emerson Страницы: 104

Бренд: Emerson Страницы: 86

Бренд: Emerson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды