Emerson Fisher D3 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 36

Emerson Fisher D3 Скачать руководство пользователя страница 11

Instruction Manual

D103460X012

D3 Valve with easy-Drive Actuator

October 2017

11

signal or to the value in Modbus register 40001. A value of 0 in register 40034 will result in the actuator responding to
the value in 40001 and a value of 1 will result in the actuator responding to physical control signals.

Note

If an actuator is on/off, a Modbus command of 049 in register 40001 will cause the valve to close fully, while a value of 50100 will
cause the valve to open fully.

Local to Modbus Control

Modbus

D

Set register 40034 (Control Source)

D

1 = Local Control

D

0 = Modbus control

Configuration Software

D

Use radio button to select Local Control or Modbus Control.

420mA to 15V Control

Modbus

D

Set register 40043 (Analog I/P mode)

D

0 = 15V

D

1 = 420mA

Configuration Software

D

Use radio button to select 420mA or 15V local analog control when Control Source is set to Local.

L2e (Dual dry contact) to Single Dry Contact Control

Modbus

D

Set register 40043 (Analog I/P mode)

D

0 = L2e (Dual dry contact)

D

1 = Single dry contact

Configuration Software

D

Use radio button to select L2e or Single pole local digital control when Control Source is set to Local.

Calibration Instructions

WARNING

To avoid personal injury or property damage, be aware that the valve will open fully and then close fully during the
calibration cycle.

«
...
9
10
11
12
13
...
»

Содержание Fisher D3





































Отзывы:

Нет отзывов