Emerson Dixell XV300K Series Скачать руководство пользователя страница 24

Страница: 24 / 26

1592016130 XV300K EN MASTER r1.1 16.06.2015

XV300K

24/26

Defines the transmission speed on channel RS-485
Possible modes:

9600

bps,

19200

bps (Def.),

38400

bps

Defines the type of parity on the serial transmission.
Possibles modes:

None

(Def.),

even

odd

Defines the parity bit in the serial transmission.
Possible modes:

=one bit (Def.),

=two bits

Adjuster’s maximum time to receive the setting value on Modbus
transmission. Over this time the adjuster locks the outputs and starts the
emergency state.
Min. 1
Max. 240s

Def. 30s

15.5

DIAGNOSIS

Days and hours of operation of the adjuster

Caution

: in case of reset this value won’t be reset

Internal temperature of the adjuster represented in Centigrades

Quantity of stops due to the missing of a power supply phase or high
disturbances in the power supply line

Quantity of stops due to the internal overheating

Quantity of stops due to an external emergency received on the terminal I4

Quantity of stops due to a breakdown/fault of the possible power supply
probe 4…20 mA

PROBE MISS.

[DI]

err

EXTERNAL

[DI]

err

OVERHEATING

[DI]

err

PHASE MISS.

[DI]

err

33.2

INT. TEMP.

[DI]

°C

[DI]

g:h

TOTAL HOURS

02:23

TIME OUT MDB

[IB]

SLA

BIT STOP

[MB]

none

PARITY

[MB]

19200 bps

BAUDRATE

[MB]

Содержание Dixell XV300K Series



























Результаты поиска

Содержание Dixell XV300K Series

Отзывы:

Похожие инструкции для Dixell XV300K Series

Бренды по названию

Популярные бренды

Emerson Dixell XV300K Series, Инструкции по установке и эксплуатации

Результаты поиска

Содержание Dixell XV300K Series

Отзывы:

Похожие инструкции для Dixell XV300K Series

Бренды по названию

Популярные бренды