1592039020 XLH210 GB r1.0 Gas Leak Detector 2016.04.26.doc
XLH210
2/2
7.
THE DISPLAY
7.1
TO ENTER IN PARAMETER CONFIGURATION
1)
Enter the “Pr1” level where the parameters are visible; press ” SET + DOWN “ for more than 3 seconds.
2)
Enter the “Pr2” level; Select “Pr2” (PAS) with
n
key and press “ SET ”.
3)
On the display will appear “0 - -” with a flashing zero.
4)
Use
o
or
n
to input the security code in the flashing digit; confirm the figure by pressing “ SET ”.
The security code is “321“.
7.2
TO CHANGE PARAMETER VALUES
1.
Enter the Programming mode.
2.
Select the required parameter.
3.
Press the “ SET ” key to display its value (that start blinking).
4.
Use
o
or
n
to change its value.
5.
Press “ SET ” to store the new value and move to the following parameter.
To exit: Press ” SET and then UP “ or wait 15s without pressing a key.
NOTE: the new values are saved even if the Programming Mode will exit by time-out.
7.3
HOW TO LOCK / UNLOCK THE KEYBOARD
+
Keep the
o
and
n
keys pressed together for more than 3s until appear:
-
“POF”= keyboard is locked
-
“Pon”= keyboard is unlocked
7.4
ON/OFF
By pushing the ON/OFF key, the instrument shows “OFF” for 5 sec. and the ON/OFF LED is
switched ON.
To put the instrument in ON mode press another time the key.
8.
MEANING OF THE LABELS
Message
Meaning
on
The controller is on and it is working correctly
oFF (label or led)
The controller is OFF (stand-by); no leakages recognized.
PAL
The pre-Alarm is active (the AHL threshold has been reached)
ALL
The Alarm is active (the AHu threshold has been reached)
AHL
Value of the Pre-Alarm threshold (modifiable with SET button)
AHu
Value of the Alarm threshold (modifiable with SET button)
PoF
The keyboard is locked
Pon
The keyboard is unlocked
Err
SEnS
The gas sensor is not connected or broken
The alarm message is displayed until the alarm condition recoveries. All the alarm messages are showed
alternating with the room temperature except for the “P1” which is flashing. To reset the “EE” alarm and restart
the normal functioning press any key, the “rSt” message is displayed for about 3s.
9.
KIND OF SENSORS
GAS: any model with 4÷20mA signal; maximum consumption not greater than 4V/A.
Note:
•
The sensors can be provided by Dixell with a different P/N (the P/N depend on the gas type). Please
check with our sales department.
The sensors can recognize the following gas: R134A, R410A, R407C, R404A, R507A, R407A, R407F
R744, R290.
The sensor can be IP41 or IP66. Please check with our sales department.
•
There is a 5-minute power-up delay to allow the sensor to stabilise.
The green LED will flash at 1 second intervals during the warm-up.
•
In an alarm condition:
o
green LED stays on and the red LED is on
o
audible alarm operates (if not disabled and after delay, if set).
o
relay output activates (after a delay, if set)
o
I output changes proportionally with gas concentration.
In a fault condition:
o
green LED will be off and the red LED will be on
o
current fault output will activate: 2mA on the 4-20mA output
10.
TECHNICAL DATA
Housing: self extinguishing ABS
Case: frontal 210x230 mm; depth 87mm
Mounting: See par. 3
Protection: IP65
Connections: Screw terminal block
≤
2,5mm
2
wiring
Power supply: 230Vac 50/60Hz
±
10%
Power absorption: 7VA max
Display:3 digits, red LED; 3 digits, yellow LED low
Inputs: 4÷20mA input
Digital inputs: door switch, free voltage
Relay outputs: Alarm (oA2): 16A 250V
Light (oA1): 16A 250Vac
Pre-Alarm (0A4): 8A 250Vac
Other outputs: Buzzer (Standard)
Direct RS485 (optional)
Data storing: on the non-volatile memory (EEPROM)
Kind of action: 1B
Pollution grade: normal
Software class: A
Operating temperature: 0÷60°C
Storage temperature: -25÷60°C
Relative humidity: 20
÷
85% (no condensing)
Resolution: 1% or 0.1% (selectable)
11.
DEFAULT SETTING VALUES
Label Description
Range
Value Menù
rEH Resolution for gas sensor
in ÷ Hd
Hd
Pr2
tib Timeout inhibition buzzer
0 ÷ 250 min
3
Pr1
AHL Threshold gas pre-alarm
0% ÷ AHu
50.0
Pr1
AHu Threshold gas alarm
AHL ÷ 100%
80.0
Pr1
AHH Gas alarm recovery differential
0.5 ÷ 25 %
10.0
Pr1
AHd Gas alarm delay
0 ÷ 250 min
0
Pr1
dHo Delay of gas alarm at start-up
0.0 ÷ 23.5 hours
0.0.
Pr1
o3 Gas sensor calibration
-10 ÷ 10 %
0.0
Pr2
P3P Gas sensor presence
n = not present; Y = present
Y
Pr2
Lci Readout with 4 mA
-999% ÷ uci
0
Pr2
uci Readout with 20 mA
LCi ÷ 999%
100
Pr2
i2P Door switch digital input polarity
cL =open / oP = close
oP
Pr1
AS Alarm relay polarity
cL =open / oP = close
oP
Pr1
Adr RS485 serial address
1÷247
1
Pr1
Ptb Parameter table
read only
-
Pr2
rEL Software release
read only
-
Pr1
Pr2 Access to the protected parameter list
-
321
Pr1
Display with the
status of the
controller
(see
section 8)
Value (%)
measured by the
sensor; within the
values between
the parameters
“Lci” and “uci”
