Emerson Damcos KC 125 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 46

Emerson Damcos KC 125 Скачать руководство пользователя страница 15

Mounting the Actuator to the Valve

Quick Installation Guide

February 2020

QIG 8000-81-003 Ed 01

13

9.

Mount the four screws (a).
Do not tighten yet.

10.

Slowly operate the hand
pump (b) to press the
actuator and the valve
bonnet together (c) until
there is a tight fit between
the actuator flange and
the valve top flange. This
operation presses the pis-
ton into the actuator and
establish the preload.

11.

Tighten the four screws (a) to torque (Newton meters) according to the table below.

12.

Use the hydraulic hand pump to fully open and fully close the actuator, and check that the
spindle moves the distance according to the specified stroke for the valve and actuator.

13.

Use a fork wrench to hold the spindle in place, while at the same time, using a fork wrench to
tighten the stem counter-nut against the actuator spindle end.

Quality

Size

Stainless

70

Stainless

80

Steel

8.8

Steel

10.9

Steel

12.9

M 4

2.9

4

4.9

M 5

4.1

5.4

5.7

8.1

9.7

M 6

7

9.3

9.8

14

17

M 8

17

22

24

33

40

M 10

33

44

47

65

79

M 12

57

76

81

114

136

M 16

140

187

197

277

333

M 20

273

364

385

541

649

M 24

472

630

665

935

1120

M 30

1310

1840

2210

«
...
13
14
15
16
17
...
»

Содержание Damcos KC 125















































Отзывы:

Нет отзывов