manualshive.com logo in svg

Emerson Copeland OLE-49, Инструкции по применению

Поделиться
Скачать
Emerson Copeland OLE-49 Скачать руководство пользователя страница 31

 

26 

 

 AGL_Unit_LOCU_EN_Rev00 

2.22.2  Ambient temperature sensor 

An ambient temperature sensor supplied by Emerson is connected to the electronic controller. This 
temperature sensor has  several  f unctionalities like  emergency mode control, lower  f an  speed 
limitation and crankcase heater control. 

2.22.3  Refrigerant level control 

– Leak detection device 

The liquid receiver is equipped with an external liquid level watch LW4-L120 from Alco Controls. This 
device provides a digital signal to the XCM25D system controller in case of low charging level inside 
the receiver. As a result, system leakage can be detected and communicated at a very early stage. 

The LW4-L120 device is connected to the digital input 

DI3

 (terminals X1.65/66/67). 

2.22.4  Fan failure 

– Fan feedback 

Thanks to the introduction of EC fan technology the XCM25D system controller gets feedback from 
the  f ans about their condition. In  case of  f ailure the digital input 

DI7

 (terminals X1.55/56/57) is 

activated and a f an alarm is generated. 

2.23  Alarm output (DO5) of the XCM25D controller 

The  digital output 

DO5

 is pre-configured as an alarm contact. The relay (max. 5  A, 250  V AC) is 

activated in case of alarms and lockouts. Warnings will be shown only on the controller display. 

This setting can be adjusted using parameter 

S01

. 

 

 

Содержание Copeland OLE-49



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды