Emerson Copeland OLE-49 Скачать руководство пользователя | Manualshive

Страница: 24 / 58

background image

AGL_Unit_LOCU_EN_Rev00

19

2.11.7 Fast access menu

The f ast access menu contains the list of probes and some values that are automatically evaluated
by the board such as the superheat and the percentage of valve opening.

"nP"

or

"noP"

stands f or "Probe not present" or "Value not evaluated".

"Err"

means "Value out of

range" or "Probe damaged, not connected or incorrectly configured".

Entering the fast
access menu

Press and release the

UP

arrow. In case of inactivity the

menu remains displayed for 3 minutes.
The values that will be displayed depend on the
conf iguration of the board.

Use the

or

arrow to select
an entry, then
press

to see the value
or to go on with
another value.

▪

P1P: Pressure value of the P1 probe (suction pressure)

▪

P2t: Temperature value of the P2 probe (not valid)

▪

P2P: Pressure value of the P2 probe (discharge pressure)

▪

P3t: Temperature value of the P3 probe (discharge line

temperature)

▪

P4t: Temperature value of the P4 probe = not available

▪

P5t: Temperature value of the P5 probe = not available

▪

P6t: Temperature value of the P6 probe (ambient temperature)

▪

P7t: Temperature value of the P7 probe (free)

▪

SH: Value of superheat. nA = not available

▪

oPP: Percentage of step valve opening = not available

▪

LInJ: Status of the liquid line solenoid (

"

On

"

–

"

Off

"

). This information

is available only if one relay is set as

"

Liquid Line Solenoid

"

.

▪

SEtd: Value of the dynamic setpoint (condenser f an SET). This

inf ormation is available only if the dynamic setpoint f unction is
enabled.

▪

AOO: Percentage of the analogue output (0-10 V or TRIAC PWM

Mod.). This inf ormation is available only if the 0-10 V or TRIAC PWM
Mod. is enabled.

▪

dSO: Percentage of the PWM output driving the valve of the digital

scroll compressor

▪

L°t: Minimum room temperature

▪

H°t: Maximum room temperature

▪

HM: Menu

▪

tU1: Voltage reading V1

▪

tU2: Voltage reading V2

▪

tU3: Voltage reading V3

▪

tA1: Current reading I1

▪

tA2: Current reading I2

Exit

Press simultaneously or wait for the timeout of about
60 seconds

Table 16: Fast access menu

2.12 Controller keyboard

2.12.1 How to lock the keyboard

Keep the

and

keys pressed simultaneously for more than 3 seconds. The

"PoF"

message

will be displayed and the keyboard will be locked. At this point it is only possible to see the setpoint
or the maximum or minimum temperatures stored. If a key is pressed for more than 3 seconds, the

"PoF"

message will be displayed.

2.12.2 How to unlock the keyboard

Keep the

and

keys pressed simultaneously for more than 3 seconds, till the

"Pon"

message

is displayed.

«
...
22
23
24
25
26
...
»

Содержание Copeland OLE-49



























































Отзывы:

Нет отзывов

Похожие инструкции для Copeland OLE-49

Бренд: Danby Страницы: 24

Бренд: Samsung Страницы: 260

Бренд: Samsung Страницы: 84

Бренд: Samsung Страницы: 84

Бренд: Coolzone Страницы: 10

Бренд: Palsonic Страницы: 9

Бренд: TECO Страницы: 18

Бренд: IFB Страницы: 8

CoolMatic HDC-270

Бренд: Waeco Страницы: 176

Бренд: Fridgemaster Страницы: 27

Refrigerator-freezers

Бренд: Smeg Страницы: 16

Бренд: ECG Страницы: 116

Бренд: Lec Страницы: 20

Бренд: Norcold Страницы: 24

Бренд: Samsung Страницы: 35

Бренд: Samsung Страницы: 18

Бренд: TCL Страницы: 85

Бренд: Zanussi Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды