manualshive.com logo in svg

Emerson Copeland OLE-49, Инструкции по применению

Поделиться
Скачать
Emerson Copeland OLE-49 Скачать руководство пользователя страница 16

 

 

 

AGL_Unit_LOCU_EN_Rev00 

 

11 

2.9  Main components description 

 

Figure 10: Main components of  LOCU units 

2.9.1  Bill of material 501 

– General description 

The  standard bill of material f or OMTE, OLE & OLTE units is 501. In general, these units have an 
air-cooled condenser with 1 or 2 EC f ans for condensing temperature control. 

For OMTE and OLTE units, a Tandem set of 2 scroll compressors (ZB** for OMTE, ZF** f or OLTE) 
provides the required cooling capacity. One of the compressors is always a digital scroll, which allows 
modulation to very low part-load conditions. 

The compressors in OLE and OLTE units have LIV technology inside. 

All compressors are equipped with a high-efficiency sound shell for best sound performance. 

An oil management system with a combined oil separator (including the reservoir) and oil injection 
devices secure sufficient compressor oil levels. Unit models OMTE -76D and OMTE-90D have only 
the oil separator with oil return into the suction line. 

An  electronic controller XCM25D will  handle  suction pressure regulation, f an  speed control in 
standard and heat recovery conditions, as well as system safety. Main safety features provided by 
the controller: compressor oil level control (only for OMTE-152D), discharge temperature protection, 
voltage sensing, refrigerant charge level control and high- and low-pressure safety. 

2.9.2  Bill of material 502 

– General description 

The BOM 502 version is only available for OMTE units. This version is prearranged for heat recovery 
(HR). Mechanically the unit has connections for external piping in the discharge line. An additional 
ball  valve  between  the  2  connection ports allows the  manual  activation of  the  heat  recovery 
f unctionality. 

For heat recovery activation the controller settings have to be adjusted. The controller hardware 
remains the same as in the standard unit. 

All other f eatures and equipment are the same as in version 501. 

NOTE: Please refer to section 2.16 "Heat recovery mode 

– Optional" for more details. 

2.9.3  Compressor 

Unit 

Standard scroll 

compressor 

Digital scroll 

compressor 

OMTE-76D-TFD 

ZB38KCE-TFD-551 

ZBD38KCE-TFD-551 

OMTE-90D-TFD 

ZB45KCE-TFD-551 

ZBD45KCE-TFD-551 

OMTE-152D-TFD 

ZB76K5E-TFD-567 

ZBD76K5E-TFD-567 

OLE-49-TFD 

ZF49K5E-TFD 

 

OLTE-82D-TFD 

ZF41K5E-TFD-567 

ZFD41K5E-TFD-567 

Table 10: Compressor model overview 

Содержание Copeland OLE-49



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды